You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
130 lines
2.7 KiB
130 lines
2.7 KiB
## UNITS.INI
|
|
## GEX v1.0.0 on STM32F072-HUB
|
|
## built Jun 15 2018 at 13:45:28
|
|
|
|
[UNITS]
|
|
# Create units by adding their names next to a type (e.g. DO=A,B),
|
|
# remove the same way. Reload to update the unit sections below.
|
|
|
|
# Digital output
|
|
DO=areset
|
|
# Digital input with triggers
|
|
DI=psign
|
|
# Neopixel RGB LED strip
|
|
NPX=
|
|
# I2C master
|
|
I2C=
|
|
# SPI master
|
|
SPI=spi
|
|
# Serial port
|
|
USART=
|
|
# 1-Wire master
|
|
1WIRE=
|
|
# Analog/digital converter
|
|
ADC=adc
|
|
# Shift register driver (595, 4094)
|
|
SIPO=
|
|
# Frequency and pulse measurement
|
|
FCAP=fcap
|
|
# Capacitive touch sensing
|
|
TOUCH=
|
|
# Simple PWM output
|
|
PWMDIM=
|
|
# Two-channel analog output with waveforms
|
|
DAC=
|
|
|
|
[DO:areset@1]
|
|
# Port name
|
|
port=A
|
|
# Pins (comma separated, supports ranges)
|
|
pins=8
|
|
# Initially high pins
|
|
initial=8
|
|
# Open-drain pins
|
|
open-drain=
|
|
|
|
[DI:psign@2]
|
|
# Port name
|
|
port=A
|
|
# Pins (comma separated, supports ranges)
|
|
pins=3
|
|
# Pins with pull-up
|
|
pull-up=
|
|
# Pins with pull-down
|
|
pull-down=
|
|
|
|
# Trigger pins activated by rising/falling edge
|
|
trig-rise=
|
|
trig-fall=
|
|
# Trigger pins auto-armed by default
|
|
auto-trigger=
|
|
# Triggers hold-off time (ms)
|
|
hold-off=100
|
|
|
|
[SPI:spi@3]
|
|
# Peripheral number (SPIx)
|
|
device=1
|
|
# Pin mappings (SCK,MISO,MOSI)
|
|
# SPI1: (0) A5,A6,A7 (1) B3,B4,B5
|
|
# SPI2: (0) B13,B14,B15
|
|
remap=0
|
|
|
|
# Prescaller: 2,4,8,...,256
|
|
prescaller=64
|
|
# Clock polarity: 0,1 (clock idle level)
|
|
cpol=1
|
|
# Clock phase: 0,1 (active edge, 0-first, 1-second)
|
|
cpha=1
|
|
# Transmit only, disable MISO
|
|
tx-only=N
|
|
# Bit order (LSB or MSB first)
|
|
first-bit=MSB
|
|
|
|
# SS port name
|
|
port=A
|
|
# SS pins (comma separated, supports ranges)
|
|
pins=14
|
|
|
|
[ADC:adc@4]
|
|
# Enabled channels, comma separated
|
|
# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
|
|
# A0 A1 A2 A3 A4 A5 A6 A7 B0 B1 C0 C1 C2 C3 C4 C5 Tsens Vref
|
|
channels=1-2, 17
|
|
|
|
# Sampling time (0-7)
|
|
sample_time=2
|
|
# Sampling frequency (Hz)
|
|
frequency=10000
|
|
|
|
# Sample buffer size
|
|
# - shared by all enabled channels
|
|
# - defines the maximum pre-trigger size (divide by # of channels)
|
|
# - captured data is sent in half-buffer chunks
|
|
# - buffer overrun aborts the data capture
|
|
buffer_size=256
|
|
|
|
# Enable continuous sampling with averaging
|
|
# Caution: This can cause DAC output glitches
|
|
averaging=Y
|
|
# Exponential averaging coefficient (permil, range 0-1000 ~ 0.000-1.000)
|
|
# - used formula: y[t]=(1-k)*y[t-1]+k*u[t]
|
|
# - not available when a capture is running
|
|
avg_factor=800
|
|
|
|
[FCAP:fcap@5]
|
|
# Signal input pin - one of:
|
|
# Full support: A0, A5, A15
|
|
# Indirect only: A1, B3
|
|
pin=A0
|
|
|
|
# Active level or edge (0-low,falling; 1-high,rising)
|
|
active-level=1
|
|
# Input filtering (0-15)
|
|
input-filter=0
|
|
# Pulse counter pre-divider (1,2,4,8)
|
|
direct-presc=1
|
|
# Pulse counting interval (ms)
|
|
direct-time=1000
|
|
|
|
# Mode on startup: N-none, I-indirect, D-direct, F-free count
|
|
initial-mode=N
|
|
|