B3M38SPD seminar project - beehive monitor with LoRa reporting
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

464 lines
17 KiB

7 years ago
/**
******************************************************************************
* @file stm32l0xx_hal_pwr.h
* @author MCD Application Team
* @brief Header file of PWR HAL module.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32L0xx_HAL_PWR_H
#define __STM32L0xx_HAL_PWR_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32l0xx_hal_def.h"
/** @addtogroup STM32L0xx_HAL_Driver
* @{
*/
/** @defgroup PWR PWR
* @{
*/
/** @defgroup PWR_Exported_Types PWR Exported Types
* @{
*/
/**
* @brief PWR PVD configuration structure definition
*/
typedef struct
{
uint32_t PVDLevel; /*!< PVDLevel: Specifies the PVD detection level.
This parameter can be a value of @ref PWR_PVD_detection_level */
uint32_t Mode; /*!< Mode: Specifies the operating mode for the selected pins.
This parameter can be a value of @ref PWR_PVD_Mode */
}PWR_PVDTypeDef;
/**
* @}
*/
/** @addtogroup PWR_Private
* @{
*/
#define PWR_EXTI_LINE_PVD EXTI_FTSR_TR16 /*!< External interrupt line 16 Connected to the PVD EXTI Line */
/**
* @}
*/
/** @defgroup PWR_Exported_Constants PWR Exported Constants
* @{
*/
/** @defgroup PWR_register_alias_address PWR Register alias address
* @{
*/
#define PWR_WAKEUP_PIN1 PWR_CSR_EWUP1
#define PWR_WAKEUP_PIN2 PWR_CSR_EWUP2
#if defined (STM32L011xx) || defined (STM32L021xx) || defined (STM32L031xx) || defined (STM32L041xx) || defined (STM32L071xx) || \
defined (STM32L072xx) || defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
#define PWR_WAKEUP_PIN3 PWR_CSR_EWUP3
#endif
/**
* @}
*/
/** @defgroup PWR_PVD_detection_level PVD detection level
* @{
*/
#define PWR_PVDLEVEL_0 PWR_CR_PLS_LEV0
#define PWR_PVDLEVEL_1 PWR_CR_PLS_LEV1
#define PWR_PVDLEVEL_2 PWR_CR_PLS_LEV2
#define PWR_PVDLEVEL_3 PWR_CR_PLS_LEV3
#define PWR_PVDLEVEL_4 PWR_CR_PLS_LEV4
#define PWR_PVDLEVEL_5 PWR_CR_PLS_LEV5
#define PWR_PVDLEVEL_6 PWR_CR_PLS_LEV6
#define PWR_PVDLEVEL_7 PWR_CR_PLS_LEV7 /* External input analog voltage
(Compare internally to VREFINT) */
/**
* @}
*/
/** @defgroup PWR_PVD_Mode PWR PVD Mode
* @{
*/
#define PWR_PVD_MODE_NORMAL ((uint32_t)0x00000000U) /*!< basic mode is used */
#define PWR_PVD_MODE_IT_RISING ((uint32_t)0x00010001U) /*!< External Interrupt Mode with Rising edge trigger detection */
#define PWR_PVD_MODE_IT_FALLING ((uint32_t)0x00010002U) /*!< External Interrupt Mode with Falling edge trigger detection */
#define PWR_PVD_MODE_IT_RISING_FALLING ((uint32_t)0x00010003U) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
#define PWR_PVD_MODE_EVENT_RISING ((uint32_t)0x00020001U) /*!< Event Mode with Rising edge trigger detection */
#define PWR_PVD_MODE_EVENT_FALLING ((uint32_t)0x00020002U) /*!< Event Mode with Falling edge trigger detection */
#define PWR_PVD_MODE_EVENT_RISING_FALLING ((uint32_t)0x00020003U) /*!< Event Mode with Rising/Falling edge trigger detection */
/**
* @}
*/
/** @defgroup PWR_Regulator_state_in_SLEEP_STOP_mode PWR Regulator state in SLEEP/STOP mode
* @{
*/
#define PWR_MAINREGULATOR_ON ((uint32_t)0x00000000U)
#define PWR_LOWPOWERREGULATOR_ON PWR_CR_LPSDSR
/**
* @}
*/
/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry
* @{
*/
#define PWR_SLEEPENTRY_WFI ((uint8_t)0x01U)
#define PWR_SLEEPENTRY_WFE ((uint8_t)0x02U)
/**
* @}
*/
/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry
* @{
*/
#define PWR_STOPENTRY_WFI ((uint8_t)0x01U)
#define PWR_STOPENTRY_WFE ((uint8_t)0x02U)
/**
* @}
*/
/** @defgroup PWR_Regulator_Voltage_Scale PWR Regulator Voltage Scale
* @{
*/
#define PWR_REGULATOR_VOLTAGE_SCALE1 PWR_CR_VOS_0
#define PWR_REGULATOR_VOLTAGE_SCALE2 PWR_CR_VOS_1
#define PWR_REGULATOR_VOLTAGE_SCALE3 PWR_CR_VOS
#define IS_PWR_VOLTAGE_SCALING_RANGE(RANGE) (((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \
((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE2) || \
((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE3))
/**
* @}
*/
/** @defgroup PWR_Flag PWR Flag
* @{
*/
#define PWR_FLAG_WU PWR_CSR_WUF
#define PWR_FLAG_SB PWR_CSR_SBF
#define PWR_FLAG_PVDO PWR_CSR_PVDO
#define PWR_FLAG_VREFINTRDY PWR_CSR_VREFINTRDYF
#define PWR_FLAG_VOS PWR_CSR_VOSF
#define PWR_FLAG_REGLP PWR_CSR_REGLPF
/**
* @}
*/
/**
* @}
*/
/** @defgroup PWR_Exported_Macro PWR Exported Macros
* @{
*/
/** @brief macros configure the main internal regulator output voltage.
* When exiting Low Power Run Mode or during dynamic voltage scaling configuration,
* the reference manual recommends to poll PWR_FLAG_REGLP bit to wait for the regulator
* to reach main mode (resp. to get stabilized) for a transition from 0 to 1.
* Only then the clock can be increased.
*
* @param __REGULATOR__: specifies the regulator output voltage to achieve
* a tradeoff between performance and power consumption when the device does
* not operate at the maximum frequency (refer to the datasheets for more details).
* This parameter can be one of the following values:
* @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode,
* System frequency up to 32 MHz.
* @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode,
* System frequency up to 16 MHz.
* @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode,
* System frequency up to 4.2 MHz
* @retval None
*/
#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) (MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)))
/** @brief Check PWR flag is set or not.
* @param __FLAG__: specifies the flag to check.
* This parameter can be one of the following values:
* @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
* was received from the WKUP pin or from the RTC alarm (Alarm B),
* RTC Tamper event, RTC TimeStamp event or RTC Wakeup.
* An additional wakeup event is detected if the WKUP pin is enabled
* (by setting the EWUP bit) when the WKUP pin level is already high.
* @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
* resumed from StandBy mode.
* @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
* by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode.
* For this reason, this bit is equal to 0 after Standby or reset
* until the PVDE bit is set.
* @arg PWR_FLAG_VREFINTRDY: Internal voltage reference (VREFINT) ready flag.
* This bit indicates the state of the internal voltage reference, VREFINT.
* @arg PWR_FLAG_VOS: Voltage Scaling select flag. A delay is required for
* the internal regulator to be ready after the voltage range is changed.
* The VOSF bit indicates that the regulator has reached the voltage level
* defined with bits VOS of PWR_CR register.
* @arg PWR_FLAG_REGLP: Regulator LP flag. When the MCU exits from Low power run
* mode, this bit stays at 1 until the regulator is ready in main mode.
* A polling on this bit is recommended to wait for the regulator main mode.
* This bit is reset by hardware when the regulator is ready.
* @retval The new state of __FLAG__ (TRUE or FALSE).
*/
#define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__))
/** @brief Clear the PWR pending flags.
* @param __FLAG__: specifies the flag to clear.
* This parameter can be one of the following values:
* @arg PWR_FLAG_WU: Wake Up flag
* @arg PWR_FLAG_SB: StandBy flag
*/
#define __HAL_PWR_CLEAR_FLAG(__FLAG__) SET_BIT(PWR->CR, (__FLAG__) << 2U)
/**
* @brief Enable interrupt on PVD Exti Line 16.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
/**
* @brief Disable interrupt on PVD Exti Line 16.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
/**
* @brief Enable event on PVD Exti Line 16.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
/**
* @brief Disable event on PVD Exti Line 16.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
/**
* @brief PVD EXTI line configuration: set falling edge trigger.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
/**
* @brief Disable the PVD Extended Interrupt Falling Trigger.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
/**
* @brief PVD EXTI line configuration: set rising edge trigger.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
/**
* @brief Disable the PVD Extended Interrupt Rising Trigger.
* This parameter can be:
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
/**
* @brief PVD EXTI line configuration: set rising & falling edge trigger.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE() do { __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); } while(0);
/**
* @brief Disable the PVD Extended Interrupt Rising & Falling Trigger.
* This parameter can be:
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE() do { __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); } while(0);
/**
* @brief Check whether the specified PVD EXTI interrupt flag is set or not.
* @retval EXTI PVD Line Status.
*/
#define __HAL_PWR_PVD_EXTI_GET_FLAG() (EXTI->PR & (PWR_EXTI_LINE_PVD))
/**
* @brief Clear the PVD EXTI flag.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG() (EXTI->PR = (PWR_EXTI_LINE_PVD))
/**
* @brief Generate a Software interrupt on selected EXTI line.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD)
/**
* @brief Generate a Software interrupt on selected EXTI line.
* @retval None.
*/
#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD)
/**
* @}
*/
/** @addtogroup PWR_Private
* @{
*/
#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \
((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \
((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \
((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7))
#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \
((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \
((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \
((MODE) == PWR_PVD_MODE_NORMAL))
#if defined (STM32L071xx) || defined (STM32L072xx) || defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
((PIN) == PWR_WAKEUP_PIN2) || \
((PIN) == PWR_WAKEUP_PIN3))
#elif defined (STM32L051xx) || defined (STM32L052xx) || defined (STM32L053xx) || defined (STM32L061xx) || defined (STM32L062xx) || defined (STM32L063xx)
#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
((PIN) == PWR_WAKEUP_PIN2))
#elif defined (STM32L031xx) || defined (STM32L041xx)
#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
((PIN) == PWR_WAKEUP_PIN2))
#elif defined (STM32L011xx) || defined (STM32L021xx)
#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
((PIN) == PWR_WAKEUP_PIN3))
#endif
#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \
((REGULATOR) == PWR_LOWPOWERREGULATOR_ON))
#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE))
#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE))
/**
* @}
*/
/* Include PWR HAL Extension module */
#include "stm32l0xx_hal_pwr_ex.h"
/** @defgroup PWR_Exported_Functions PWR Exported Functions
* @{
*/
/** @defgroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions
* @{
*/
void HAL_PWR_DeInit(void);
void HAL_PWR_EnableBkUpAccess(void);
void HAL_PWR_DisableBkUpAccess(void);
/**
* @}
*/
/** @defgroup PWR_Exported_Functions_Group2 Low Power modes configuration functions
* @{
*/
/* PVD control functions ************************************************/
void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD);
void HAL_PWR_EnablePVD(void);
void HAL_PWR_DisablePVD(void);
void HAL_PWR_PVD_IRQHandler(void);
void HAL_PWR_PVDCallback(void);
/* WakeUp pins configuration functions ****************************************/
void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx);
void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx);
/* Low Power modes configuration functions ************************************/
void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry);
void HAL_PWR_EnterSTANDBYMode(void);
void HAL_PWR_EnableSleepOnExit(void);
void HAL_PWR_DisableSleepOnExit(void);
void HAL_PWR_EnableSEVOnPend(void);
void HAL_PWR_DisableSEVOnPend(void);
/**
* @}
*/
/**
* @}
*/
/* Define the private group ***********************************/
/**************************************************************/
/** @defgroup PWR_Private PWR Private
* @{
*/
/**
* @}
*/
/**************************************************************/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32L0xx_HAL_PWR_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/