Nevar pievienot vairāk kā 25 tēmas
Tēmai ir jāsākas ar burtu vai ciparu, tā var saturēt domu zīmes ('-') un var būt līdz 35 simboliem gara.
99 rindas
1.4 KiB
99 rindas
1.4 KiB
#include "init.h"
|
|
|
|
#include "utils/gpio.h"
|
|
#include "utils/usart.h"
|
|
#include "utils/nvic.h"
|
|
|
|
|
|
void init_gpios(void)
|
|
{
|
|
gpio_enable(GPIOA);
|
|
gpio_enable(GPIOB);
|
|
gpio_enable(GPIOC);
|
|
|
|
// LEDs
|
|
gpio_set_mode(GPIOC, BIT8 | BIT9, MODER_OUTPUT);
|
|
}
|
|
|
|
|
|
|
|
void init_clock(void)
|
|
{
|
|
// Flash timing - 64-bit access, pre-fetch, latency = 1
|
|
FLASH_ACR |= FLASH_ACR_ACC64; // Cannot write both at once
|
|
FLASH_ACR |= FLASH_ACR_PRFTEN | FLASH_ACR_LATENCY;
|
|
|
|
// Power on HSI (runs from MSI on start)
|
|
RCC_CR |= RCC_CR_HSION;
|
|
|
|
// Wait for HSIRDY
|
|
while (!(RCC_CR & RCC_CR_HSIRDY));
|
|
|
|
// Select HSI as the core clock source
|
|
RCC_CFGR &= ~RCC_CFGR_SW;
|
|
RCC_CFGR |= RCC_CFGR_SW_HSI;
|
|
}
|
|
|
|
|
|
|
|
void init_usart(void)
|
|
{
|
|
gpio_set_af(GPIOA, BIT2 | BIT3, AF7);
|
|
|
|
// USART at A2 (tx), A3 (rx)
|
|
RCC_APB1ENR |= RCC_APB1ENR_USART2EN;
|
|
|
|
// RATE 9600Bd 104.1875 (see datasheet for reference)
|
|
//USART2_BRR = 0x00683; // 9600 @ 16MHz
|
|
USART2_BRR = 0x0008A; // 115200 @ 16MHz
|
|
|
|
// USART enable
|
|
USART2_CR1 = USART_CR1_UE | USART_CR1_RE | USART_CR1_TE;
|
|
|
|
// enable interrupt on data receive
|
|
nvic_enable_irq(NVIC_USART2_IRQ);
|
|
USART2_CR1 |= USART_CR1_RXNEIE;
|
|
}
|
|
|
|
|
|
|
|
void init_systick(void)
|
|
{
|
|
SysTick_CSR = (SysTick_CSR & ~SysTick_CSR_CLKSOURCE) | SysTick_CSR_CLKSOURCE_CORE;
|
|
SysTick_RELOAD = 16000; // 1ms interrupt @ 16MHz core clock
|
|
SysTick_CSR |= SysTick_CSR_TICKINT | SysTick_CSR_ENABLE;
|
|
}
|
|
|
|
|
|
void init_adc(void)
|
|
{
|
|
gpio_set_mode(GPIOB, BIT12, MODER_ANALOG);
|
|
|
|
// TODO
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|