tuner_r82xx: turn off loop-through, remove dead code

As pointed out by Carl Laufer on the mailing list,
turning the loop-through output off reduces the
current consumption by 10-20mA which in turn reduces
the heat a bit. So far there seem to be no devices
that have anything connected to the loop-through output.

Signed-off-by: Steve Markgraf <steve@steve-m.de>

src/tuner_r82xx.c

@@ -770,20 +770,7 @@ static int r82xx_set_tv_standard(struct r82xx_priv *priv,
 	uint8_t lt_att, flt_ext_widest, polyfil_cur;
 	int need_calibration;
 
-	if (delsys == SYS_ISDBT) {
-		if_khz = 4063;
-		filt_cal_lo = 59000;
-		filt_gain = 0x10;	/* +3db, 6mhz on */
-		img_r = 0x00;		/* image negative */
-		filt_q = 0x10;		/* r10[4]:low q(1'b1) */
-		hp_cor = 0x6a;		/* 1.7m disable, +2cap, 1.25mhz */
-		ext_enable = 0x40;	/* r30[6], ext enable; r30[5]:0 ext at lna max */
-		loop_through = 0x00;	/* r5[7], lt on */
-		lt_att = 0x00;		/* r31[7], lt att enable */
-		flt_ext_widest = 0x00;	/* r15[7]: flt_ext_wide off */
-		polyfil_cur = 0x60;	/* r25[6:5]:min */
-	} else {
-		if (bw <= 6) {
+	/* BW < 6 MHz */
 	if_khz = 3570;
 	filt_cal_lo = 56000;	/* 52000->56000 */
 	filt_gain = 0x10;	/* +3db, 6mhz on */
@@ -791,57 +778,10 @@ static int r82xx_set_tv_standard(struct r82xx_priv *priv,
 	filt_q = 0x10;		/* r10[4]:low q(1'b1) */
 	hp_cor = 0x6b;		/* 1.7m disable, +2cap, 1.0mhz */
 	ext_enable = 0x60;	/* r30[6]=1 ext enable; r30[5]:1 ext at lna max-1 */
-			loop_through = 0x00;	/* r5[7], lt on */
-			lt_att = 0x00;		/* r31[7], lt att enable */
-			flt_ext_widest = 0x00;	/* r15[7]: flt_ext_wide off */
-			polyfil_cur = 0x60;	/* r25[6:5]:min */
-		} else if (bw == 7) {
-#if 0
-			/*
-			 * There are two 7 MHz tables defined on the original
-			 * driver, but just the second one seems to be visible
-			 * by rtl2832. Keep this one here commented, as it
-			 * might be needed in the future
-			 */
-
-			if_khz = 4070;
-			filt_cal_lo = 60000;
-			filt_gain = 0x10;	/* +3db, 6mhz on */
-			img_r = 0x00;		/* image negative */
-			filt_q = 0x10;		/* r10[4]:low q(1'b1) */
-			hp_cor = 0x2b;		/* 1.7m disable, +1cap, 1.0mhz */
-			ext_enable = 0x60;	/* r30[6]=1 ext enable; r30[5]:1 ext at lna max-1 */
-			loop_through = 0x00;	/* r5[7], lt on */
+	loop_through = 0x01;	/* r5[7], lt off */
 	lt_att = 0x00;		/* r31[7], lt att enable */
 	flt_ext_widest = 0x00;	/* r15[7]: flt_ext_wide off */
 	polyfil_cur = 0x60;	/* r25[6:5]:min */
-#endif
-			/* 7 MHz, second table */
-			if_khz = 4570;
-			filt_cal_lo = 63000;
-			filt_gain = 0x10;	/* +3db, 6mhz on */
-			img_r = 0x00;		/* image negative */
-			filt_q = 0x10;		/* r10[4]:low q(1'b1) */
-			hp_cor = 0x2a;		/* 1.7m disable, +1cap, 1.25mhz */
-			ext_enable = 0x60;	/* r30[6]=1 ext enable; r30[5]:1 ext at lna max-1 */
-			loop_through = 0x00;	/* r5[7], lt on */
-			lt_att = 0x00;		/* r31[7], lt att enable */
-			flt_ext_widest = 0x00;	/* r15[7]: flt_ext_wide off */
-			polyfil_cur = 0x60;	/* r25[6:5]:min */
-		} else {
-			if_khz = 4570;
-			filt_cal_lo = 68500;
-			filt_gain = 0x10;	/* +3db, 6mhz on */
-			img_r = 0x00;		/* image negative */
-			filt_q = 0x10;		/* r10[4]:low q(1'b1) */
-			hp_cor = 0x0b;		/* 1.7m disable, +0cap, 1.0mhz */
-			ext_enable = 0x60;	/* r30[6]=1 ext enable; r30[5]:1 ext at lna max-1 */
-			loop_through = 0x00;	/* r5[7], lt on */
-			lt_att = 0x00;		/* r31[7], lt att enable */
-			flt_ext_widest = 0x00;	/* r15[7]: flt_ext_wide off */
-			polyfil_cur = 0x60;	/* r25[6:5]:min */
-		}
-	}
 
 	/* Initialize the shadow registers */
 	memcpy(priv->regs, r82xx_init_array, sizeof(r82xx_init_array));
@@ -1196,7 +1136,7 @@ int r82xx_standby(struct r82xx_priv *priv)
 	rc = r82xx_write_reg(priv, 0x06, 0xb1);
 	if (rc < 0)
 		return rc;
-	rc = r82xx_write_reg(priv, 0x05, 0x03);
+	rc = r82xx_write_reg(priv, 0x05, 0xa0);
 	if (rc < 0)
 		return rc;
 	rc = r82xx_write_reg(priv, 0x07, 0x3a);