You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
361 lines
9.7 KiB
361 lines
9.7 KiB
<div class="Box">
|
|
<h2>Troubleshooting</h2>
|
|
|
|
<ul>
|
|
<li>ESPTerm communicates with external µC via UART on pins <b>Rx</b> and <b>Tx</b>.
|
|
It can be configured in <a href="<?= url('cfg_system') ?>">System Settings</a>.
|
|
Make sure you're using the correct baud rate and other settings on the other side.
|
|
|
|
<li>Boot log and debug messages are available on pin <b>GPIO2</b> (P2) at 115200\,bps, 1 stop bit, no parity.
|
|
|
|
<li>ESPTerm uses 3.3\,V logic. For communication with 5\,V logic (eg. Aurdino), 470\,R
|
|
protection resistors are recommended. The ESPTerm breakout board already includes those resistors.
|
|
|
|
<li>If the Low Voltage Detector ("LVD") LED on the ESPTerm breakout lights up, your power connections have too high
|
|
resistance or the power supply is insufficient. ESP8266 can consume in short spikes up to 500\,A and
|
|
the supply voltage on the module must not drop below about 2.7\,V. Avoid needless breadboard jumpers and too thin wires.
|
|
|
|
<li>Connect Rx and Tx with a piece of wire to verify that the terminal works correctly; you should then immediately
|
|
see what you type in the browser. <i>This won't work if your ESP8266 board has a built-in USB-serial
|
|
converter connected to those pins.</i>
|
|
|
|
<li>For best performance, use the module in Client mode (connected to external network). Enabling AP mode consumes
|
|
extra RAM and cycles, since the captive portal DNS server and DHCP server are be loaded.
|
|
|
|
<li>In AP mode, check that the channel used by ESPTerm is clear; interference may cause flaky connection. A good mobile app to use for this is <a href="https://play.google.com/store/apps/details?id=com.farproc.wifi.analyzer">WiFi Analyzer (Google Play)</a>
|
|
|
|
<li>The terminal browser display needs WebSockets for the real-time updating to work.
|
|
It will not work with some old browsers (Android < 4.4, IE < 10, Opera Mini)
|
|
- see the <a href="https://caniuse.com/websockets/embed/">compatibility chart</a>.
|
|
|
|
<li>At most 4 clients can be connected to the AP at the same time. This is a limitation of the ESP8266 SDK.
|
|
</ul>
|
|
</div>
|
|
|
|
<div class="Box">
|
|
<h2>Screen</h2>
|
|
|
|
<ul>
|
|
<li>Most ANSI escape sequences are supported.
|
|
|
|
<li>The initial screen size and other terminal options can be configured in
|
|
<a href="<?= url('cfg_term') ?>">Terminal Settings</a>
|
|
|
|
<li>Display updates are sent to the browser after 20 ms of inactivity on the communication UART.
|
|
This is to avoid hogging the server with tiny updates during large screen repaints.
|
|
</ul>
|
|
</div>
|
|
|
|
<div class="Box theme-0">
|
|
<h2>Color Reference</h2>
|
|
|
|
<p>Color is set using <code>\e[<c>m</code> where <code><c></code> are numbers separated by semicolons
|
|
(and <code>\e</code> is ESC, code 27). The actual color representation depends on a color theme which
|
|
can be selected in <a href="<?= url('cfg_term') ?>">Terminal Settings</a>.</p>
|
|
|
|
<b>Foreground</b>
|
|
|
|
<div class="colorprev">
|
|
<span class="bg7 fg0">30</span>
|
|
<span class="bg0 fg1">31</span>
|
|
<span class="bg0 fg2">32</span>
|
|
<span class="bg0 fg3">33</span>
|
|
<span class="bg0 fg4">34</span>
|
|
<span class="bg0 fg5">35</span>
|
|
<span class="bg0 fg6">36</span>
|
|
<span class="bg0 fg7">37</span>
|
|
</div>
|
|
|
|
<div class="colorprev">
|
|
<span class="bg0 fg8">90</span>
|
|
<span class="bg0 fg9">91</span>
|
|
<span class="bg0 fg10">92</span>
|
|
<span class="bg0 fg11">93</span>
|
|
<span class="bg0 fg12">94</span>
|
|
<span class="bg0 fg13">95</span>
|
|
<span class="bg0 fg14">96</span>
|
|
<span class="bg0 fg15">97</span>
|
|
</div>
|
|
|
|
<b>Background</b>
|
|
|
|
<div class="colorprev">
|
|
<span class="bg0 fg15">40</span>
|
|
<span class="bg1 fg15">41</span>
|
|
<span class="bg2 fg15">42</span>
|
|
<span class="bg3 fg0">43</span>
|
|
<span class="bg4 fg15">44</span>
|
|
<span class="bg5 fg15">45</span>
|
|
<span class="bg6 fg15">46</span>
|
|
<span class="bg7 fg0">47</span>
|
|
</div>
|
|
|
|
<div class="colorprev">
|
|
<span class="bg8 fg15">100</span>
|
|
<span class="bg9 fg0">101</span>
|
|
<span class="bg10 fg0">102</span>
|
|
<span class="bg11 fg0">103</span>
|
|
<span class="bg12 fg0">104</span>
|
|
<span class="bg13 fg0">105</span>
|
|
<span class="bg14 fg0">106</span>
|
|
<span class="bg15 fg0">107</span>
|
|
</div>
|
|
|
|
<p>To make the text bold, use the "bold" attribute (eg. <code>\e[31;40;1m</code> for
|
|
<span style="padding: 2px;" class="bg0 fg1 bold">bold red on black</span>).</p>
|
|
|
|
<p>The colors are reset to default using <code>\e[0m</code>. For more info, see the tables below.</p>
|
|
</div>
|
|
|
|
<div class="Box">
|
|
<h2>User Input</h2>
|
|
|
|
<p>
|
|
All the user types on their keyboard is sent as-is to the UART, including ESC, ANSI sequences for arrow keys and CR-LF for Enter.
|
|
</p>
|
|
|
|
<p>The buttons under the screen send ASCII codes 1, 2, 3, 4, 5. This choice was made to make their parsing as simple as possible.</p>
|
|
|
|
<p>
|
|
Mouse input (click/tap) is sent as <code>\e[<y>;<x>M</code>. You can use this for virtual on-screen buttons.
|
|
</p>
|
|
</div>
|
|
|
|
<div class="Box">
|
|
<h2>Supported ANSI Escape Sequences</h2>
|
|
|
|
<p>Sequences are started by ASCII code 27 (ESC, <code>\e</code>, <code>\x1b</code>, <code>\033</code>)</p>
|
|
|
|
<p>Instead of <code>\a</code> (BELL, ASCII 7) in the commands, you can use `\e\` (ESC + backslash). It's the Text Separator code.</p>
|
|
|
|
<h3>Text Attributes</h3>
|
|
|
|
<p>
|
|
All text attributes are set using <code>\e[...m</code> where the dots are numbers separated by semicolons.
|
|
You can combine up to 3 attributes in a single command.
|
|
</p>
|
|
|
|
<table class="ansiref">
|
|
<thead>
|
|
<tr>
|
|
<th>Attribute</th>
|
|
<th>Meaning</th>
|
|
</tr>
|
|
</thead>
|
|
<tbody>
|
|
<tr>
|
|
<td>0</td>
|
|
<td>Reset text attributes to default</td>
|
|
</tr>
|
|
<tr>
|
|
<td>1</td>
|
|
<td>Bold</td>
|
|
</tr>
|
|
<tr>
|
|
<td>21 or 22</td>
|
|
<td>Bold off</td>
|
|
</tr>
|
|
<tr>
|
|
<td>7</td>
|
|
<td>Inverse (fg/bg swap when printing)</td>
|
|
</tr>
|
|
<tr>
|
|
<td>27</td>
|
|
<td>Inverse OFF</td>
|
|
</tr>
|
|
<tr>
|
|
<td>30-37, 90-97</td>
|
|
<td>Foreground color, normal and bright</td>
|
|
</tr>
|
|
<tr>
|
|
<td>40-47, 100-107</td>
|
|
<td>Background color, normal and bright</td>
|
|
</tr>
|
|
</tbody>
|
|
</table>
|
|
|
|
<h3>Cursor</h3>
|
|
|
|
<p>Movement commands scroll the screen if needed. The coordinates are 1-based, origin top left.</p>
|
|
|
|
<table class="ansiref w100">
|
|
<thead>
|
|
<tr>
|
|
<th>Code</th>
|
|
<th>Params</th>
|
|
<th>Meaning</th>
|
|
</tr>
|
|
</thead>
|
|
<tbody>
|
|
<tr>
|
|
<td>\e[<n>A</td>
|
|
<td>[count]</td>
|
|
<td>Move cursor up</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[<n>B</td>
|
|
<td>[count]</td>
|
|
<td>Move cursor down</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[<n>C</td>
|
|
<td>[count]</td>
|
|
<td>Move cursor forward (right)</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[<n>D</td>
|
|
<td>[count]</td>
|
|
<td>Move cursor backward (left)</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[<n>E</td>
|
|
<td>[count]</td>
|
|
<td>Go N lines down, start of line</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[<n>F</td>
|
|
<td>[count]</td>
|
|
<td>Go N lines up, start of line</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[<n>G</td>
|
|
<td>column</td>
|
|
<td>Go to column</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[<y>;<x>G</td>
|
|
<td>[row=1];[col=1]</td>
|
|
<td>Go to row and column</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[6n</td>
|
|
<td>--</td>
|
|
<td>Query cursor position. Position is sent back as <code>\e[?;?R</code> with row;column.</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[s</td>
|
|
<td>--</td>
|
|
<td>Store position</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[u</td>
|
|
<td>--</td>
|
|
<td>Restore position</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e7</td>
|
|
<td>--</td>
|
|
<td>Store position & attributes</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e8</td>
|
|
<td>--</td>
|
|
<td>Restore position & attributes</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[?25l</td>
|
|
<td>--</td>
|
|
<td>Hide cursor</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[?25h</td>
|
|
<td>--</td>
|
|
<td>Show cursor</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[?7l</td>
|
|
<td>--</td>
|
|
<td>Disable cursor auto-wrap & auto-scroll at end of screen</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[?7h</td>
|
|
<td>--</td>
|
|
<td>Enable cursor auto-wrap & auto-scroll at end of screen</td>
|
|
</tr>
|
|
</tbody>
|
|
</table>
|
|
|
|
<h3>Screen</h3>
|
|
|
|
<table class="ansiref w100">
|
|
<thead>
|
|
<tr>
|
|
<th>Code</th>
|
|
<th>Params</th>
|
|
<th>Meaning</th>
|
|
</tr>
|
|
</thead>
|
|
<tbody>
|
|
<tr>
|
|
<td>\e[<m>J</td>
|
|
<td>[mode=0]</td>
|
|
<td>Clear screen. Mode: 0 - from cursor, 1 - to cursor, 2 - all</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[<m>K</td>
|
|
<td>[mode=0]</td>
|
|
<td>Erase line. Mode: 0 - from cursor, 1 - to cursor, 2 - all</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[<n>S</td>
|
|
<td>[lines]</td>
|
|
<td>Scroll screen content up, add empty line at the bottom</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[<n>T</td>
|
|
<td>[lines]</td>
|
|
<td>Scroll screen content down, add empty line at the top</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e]W<r>;<c>\a</td>
|
|
<td>rows;cols</td>
|
|
<td>Set screen size (max ~ 80x30). This also clears the screen. This is a custom ESPTerm OSC command.</td>
|
|
</tr>
|
|
</tbody>
|
|
</table>
|
|
|
|
<h3>System Commands</h3>
|
|
|
|
<table class="ansiref w100">
|
|
<thead>
|
|
<tr>
|
|
<th>Code</th>
|
|
<th>Params</th>
|
|
<th>Meaning</th>
|
|
</tr>
|
|
</thead>
|
|
<tbody>
|
|
<tr>
|
|
<td>\ec</td>
|
|
<td>--</td>
|
|
<td>
|
|
"Device Reset" - clear screen, reset attributes, show cursor & move it to 1,1.
|
|
The screen size and WiFi settings stay unchanged.
|
|
</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e[5n</td>
|
|
<td>--</td>
|
|
<td>Query device status, replies with <code>\e[0n</code> "device is OK". Can be used to check if the UART works.</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e]TITLE=…\a</td>
|
|
<td>Title text</td>
|
|
<td>Set terminal title. This is a custom ESPTerm OSC command.</td>
|
|
</tr>
|
|
<tr>
|
|
<td>\e]BTNn=…\a</td>
|
|
<td>1-5, label</td>
|
|
<td>Set button label. This is a custom ESPTerm OSC command.</td>
|
|
</tr>
|
|
<tr>
|
|
<td>ASCII 24 (18h)</td>
|
|
<td></td>
|
|
<td>This symbol is sent by ESPTerm when it becomes ready to receive commands. It can be used to wait before it becomes
|
|
ready on power-up, or to detect a spontaneous ESPTerm restart - that could happen due to RAM exhaustion due
|
|
to a memory leak, or perhaps a power outage.
|
|
</td>
|
|
</tr>
|
|
</tbody>
|
|
</table>
|
|
</div>
|
|
|