ESPTerm - ESP8266 terminal emulator. Branches: [master] patches, [work] next release
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
espterm-firmware/README.md

209 lines
10 KiB

# ESPTerm
8 years ago
**ESPTerm is a VT100-like terminal emulator running on the ESP8266 WiFi chip.**
7 years ago
![Photo][photo-hw]<br>
*Fig 1: Breadboard adapter developed for ESPTerm*
7 years ago
ESPTerm **passes most of VTTEST test cases**, making it functionally comparable to eg.
gnome-terminal, terminator, konsole, GtkTerm or PuTTY.
7 years ago
ESPTerm is **capable of running Midnight Commander** through agetty, **including full
7 years ago
mouse support**, provided agetty is made to believe it's Xterm, which shows ESPTerm
is compatible with ncurses.
In addition to control sequences that manipulate the terminal or user input, there
is a set of simple **networking commands** for device-to-device message exchange and
interacting with remote servers.
To see what escape sequences are supported, check out this [annotated Xterm manual page][xterm-compare]
7 years ago
which was used for reference, or the built-in help page ([online demo][demo-help])
The terminal screen can be accessed using any web browser, even on a phone or tablet.
7 years ago
It works with ESP-01, ESP-01S, ESP-12 and likely many other modules.
With ESPTerm, you can add remote access via WiFi to any embeded project, all you need is
7 years ago
UART and some imagination!
## Try it online
You can try the web user interface here: [espterm.github.io][demo-term]
The demo is almost identical to the real thing, except, of course, it doesn't do much without the
emulator backend that runs on the ESP8266. The web version will be updated to match this repository
7 years ago
after each minor release (and sometimes in between for testing; the version currently being show-cased
can be read on the About page of the demo).
### Browser support
Use the above linked online demo to verify compatibility with your browser.
To our knowledge, ESPTerm **works with**:
- Google Chrome (desktop, mobile)
- Firefox (desktop, mobile not tested)
- Safari (desktop, mobile)
- Chromium
- Opera
- Brave
- Konqueror
It **does not work with**:
- Microsoft Edge - runs, but is extremely laggy
- Internet Explorer (any version) - crashes, missing JS features
- Opera Mini - crashes, missing JS and CSS features
- Blackberry browser - not tested, but unlikely
7 years ago
- Safari on old iOS versions - missing features
- WebOS browser
- Old Android Browser (before 4.4?) - not tested, likely missing JS features
## Main features
- **Almost complete VT102 emulation** with some extras from Xterm, eg.
7 years ago
- Screen size up to 80x25 (the limit can be modified when compiling from source)
- All standard text styles and 16 colors supported
- Full UTF-8 support, alternate character sets
- Standard mouse tracking modes
- You can dynamically set screen title, button labels...
7 years ago
- **Networking commands**
- Command for sending a message to another ESPTerm
- API endpoint (`/api/v1/msg`) for receiving messages sent e.g. from a script on PC, web browser or CURL
- Command for requesting remote servers and getting back response headers and/or body
7 years ago
- **Web Terminal Interface**
7 years ago
- Real-time screen update via WebSocket
7 years ago
- Mouse and keyboard input, works also on mobile
- 5 optional buttons for quick commands
- Text file upload tool with adjustable delays and line endings
- *Built-in help page* ([demo][demo-help]) with basic troubleshooting and command reference
7 years ago
- **User-friendly comprehensive WiFi configuration** (Demo: [WiFi][demo-wifi], [network][demo-network] config)
- Static IP, DHCP, channel selection, power
- SSID search utility for finding your existing network
7 years ago
- **Basic security features**
- Possibility to password-lock parts of the web interface
- Admin password for some sensitive operations (can be changed!)
- Configurable AP password & Hidden attribute
- **Advanced settings storage**
- Stored in Flash
- Seamlesly updated and usually backwards compatible in minor releases
- Settings can be saved as defaults and later easily restored (ideal e.g. for classroom use, saving
good tested settings before giving the module to students)
## Bugs? Ideas?
To ask any questions or discuss new features you'd like to see added, it's best to use
the **[ESPTerm Dev mailing list](https://groups.google.com/forum/#!forum/espterm-dev)**
Subscribe to the mailing list to also receive new release announcements.
If you found a bug (that happens alot!), please submit it to our [bug tracker](https://github.com/espterm/espterm-firmware/issues).
We also use it to track planned ideas. If you don't want to create a GitHub account for that, just send it to the mailing list.
8 years ago
7 years ago
## Running ESPTerm
8 years ago
To run ESPTerm on your ESP8266, either build it yourself from source using `xtensa-lx106-elf-gcc`
(and the included Makefile), or download pre-built binaries from the [GitHub releases section][releases].
Flash the binaries using [esptool][esptool].
8 years ago
7 years ago
### Pins
8 years ago
7 years ago
- Pin GPIO2 is used for debug messages at 115200 baud, 8 bit, no parity.
- Pins Rx and Tx are used for the main communication UART, parameters of which can be set on the system config page.
Connect your USB-serial dongle or application microcontroller here.
8 years ago
### Setup
7 years ago
- When flashed for the first time, ESPTerm wipes any possible previous WiFi configuration, because it implements its own WiFi
config manager with many additional features.
- It should start in AP mode, the default SSID being `TERM-MACADR` with `MACADR` being three unique bytes from the MAC
address / Device ID as ASCII hex.
- Connect to the AP via a smartphone or laptop and configure WiFi as desired. If a captive portal page does not open,
try 192.168.4.1 in your web browser.
7 years ago
### Rescue from messed up config
7 years ago
It can happen that some changes to the WiFi or network config make the module inaccessible.
- To re-enable the built-in AP, hold the BOOT (GPIO0 -> GND) button for about 1 s, until the blue LED starts flashing.
Then quickly release the button.
- To reset all settings to defaults, hold the button a couple seconds until the LED flashes rapidly, then release it.
- You can cancel this wipe/reset operation (when triggered by accident) by pressing Reset or disconnecting the power supply.
7 years ago
7 years ago
### Config banks
7 years ago
ESPTerm has two config "files", one for defaults and one for the currently used settings. In the case of the terminal
config, there is also a third, temporary file for changes done via ESC commands.
7 years ago
When you get your settings *just right*, you can store them as defaults, which can then be at any time restored
by holding the BOOT (GPIO0) button. You can do this on the System Settings page. This asks for an "admin password",
7 years ago
which can (and should!) be changed. This password can't be easily recovered when forgotten.
You can also restore everything (except the saved defaults) to "factory defaults", there is a button for this
7 years ago
on the System Settings page. Those are the initial values you would get after a clean install.
## Research resources
7 years ago
Developing the terminal emulator was complicated by the information being scattered across many places and the existing
implementations I used for reference often got some details wrong or didn't implement certain features at all. Xterm proved to be by far the most complete implementation.
7 years ago
7 years ago
A great tool for checking my code has proven to be [VTTTEST][vttest]. ESPTerm passes most of the tests on the main page and some additional Xterm specific ones, like Mouse Tracking.
7 years ago
Here is a list of useful [VT100 emulation resources][resources] I've collected for reference.
8 years ago
8 years ago
## Development
ESPTerm's firmware is written in C and is based on SpriteTM's `libesphttpd` http server library forked to
7 years ago
[MightyPork/libesphttpd][httpdlib]. This fork includes various improvements and changes required by the project.
8 years ago
### Installation for development
- Clone this project with `--recursive`, or afterwards run `git submodule init` and `git submodule update`.
- Install [esp-open-sdk][opensdk] and build it with
7 years ago
`make toolchain esptool libhal STANDALONE=n`.
8 years ago
Make sure the `xtensa-lx106-elf/bin` folder is on $PATH.
- Install [esptool][esptool] (it's in the Arch community repo and on AUR, too)
8 years ago
- Set up udev rules so you have access to ttyUSB0 without root, eg:
```
KERNEL=="tty[A-Z]*[0-9]*", GROUP="uucp", MODE="0666"
```
- Install Ragel if you wish to make modifications to the ANSI sequence parser.
If not, comment out its call in `build_parser.sh`. The `.rl` file is the actual source, the `.c` is generated.
7 years ago
- Install dependencies of the front-end submodule (`yarn install` in the front-end folder, installed PHP)
8 years ago
- Make sure your `esphttpdconfig.mk` is set up properly - link to the SDK etc.
8 years ago
The IoT SDK is now included in the project due to problems with obtaining the correct version and patching it.
It works with version 1.5.2, any newer seems to be incompatible. If you get it working with a newer SDK, a PR is more
than welcome!
8 years ago
### Web resources
8 years ago
7 years ago
The web resources are in the `front-end` git submodule. To prepare the web resources for a build,
run `make web`. The resulting files are copied to `html/`. The `html/` folder is then embedded in the firmware image.
8 years ago
8 years ago
It's kind of tricky to develop the web resources locally; you might want to try the "split image"
Makefile option, then you can flash just the html portion with `make htmlflash`. I haven't tried this.
8 years ago
7 years ago
For local development, use the `server.sh` script in `html_orig` (more details in the front-end repo's readme).
It's possible to talk to the API endpoints of a running ESP8266 from a page served by your local server
if you configure `_env.php` with its IP.
8 years ago
### Flashing
8 years ago
7 years ago
The Makefile should automatically build the parser and web resources for you when you run `make`.
The web resources are normally no re-built, because the build process is quite slow. To manually rebuild them,
run `make web` before `make`.
8 years ago
7 years ago
To flash, just run `make flash`. It will use parameters you setup in the `esphttpdconfig.mk` file.
7 years ago
[releases]: https://github.com/MightyPork/esp-vt100-firmware/releases
[httpdlib]: https://github.com/MightyPork/libesphttpd
[esptool]: https://github.com/espressif/esptool
[opensdk]: https://github.com/pfalcon/esp-open-sdk/
[demo-help]: https://espterm.github.io/help.html
[demo-wifi]: https://espterm.github.io/cfg_wifi.html
[demo-network]: https://espterm.github.io/cfg_network.html
[demo-term]: https://espterm.github.io/term.html
[xterm-compare]: https://espterm.github.io/docs/espterm-xterm.html
[photo-hw]: https://espterm.github.io/docs/espterm-hw-small.jpg
[resources]: https://espterm.github.io/docs/index.html
7 years ago
[vttest]: http://invisible-island.net/vttest/