B3M38SPD seminar project - beehive monitor with LoRa reporting
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 

5110 lines
153 KiB

/**
******************************************************************************
* @file stm32l0xx_hal_tim.c
* @author MCD Application Team
* @brief TIM HAL module driver.
* @brief This file provides firmware functions to manage the following
* functionalities of the Timer (TIM) peripheral:
* + Timer Base Initialization
* + Timer Base Start
* + Timer Base Start Interruption
* + Timer Base Start DMA
* + Timer Output Compare/PWM Initialization
* + Timer Output Compare/PWM Channel Configuration
* + Timer Output Compare/PWM Start
* + Timer Output Compare/PWM Start Interruption
* + Timer Output Compare/PWM Start DMA
* + Timer Input Capture Initialization
* + Timer Input Capture Channel Configuration
* + Timer Input Capture Start
* + Timer Input Capture Start Interruption
* + Timer Input Capture Start DMA
* + Timer One Pulse Initialization
* + Timer One Pulse Channel Configuration
* + Timer One Pulse Start
* + Timer Encoder Interface Initialization
* + Timer Encoder Interface Start
* + Timer Encoder Interface Start Interruption
* + Timer Encoder Interface Start DMA
* + Timer OCRef clear configuration
* + Timer External Clock configuration
* + Timer Complementary signal bread and dead time configuration
* + Timer Master and Slave synchronization configuration
@verbatim
==============================================================================
##### TIMER Generic features #####
==============================================================================
[..] The Timer features include:
(#) 16-bit up, down, up/down auto-reload counter.
(#) 16-bit programmable prescaler allowing dividing (also on the fly) the counter clock
frequency either by any factor between 1 and 65536.
(#) Up to 4 independent channels for:
(++) Input Capture
(++) Output Compare
(++) PWM generation (Edge and Center-aligned Mode)
(++) One-pulse mode output
(#) Synchronization circuit to control the timer with external signals and to interconnect
several timers together.
(#) Supports incremental (quadrature) encoder and hall-sensor circuitry for positioning
purposes
##### How to use this driver #####
================================================================================
[..]
(#) Initialize the TIM low level resources by implementing the following functions
depending from feature used :
(++) Time Base : HAL_TIM_Base_MspInit()
(++) Input Capture : HAL_TIM_IC_MspInit()
(++) Output Compare : HAL_TIM_OC_MspInit()
(++) PWM generation : HAL_TIM_PWM_MspInit()
(++) One-pulse mode output : HAL_TIM_OnePulse_MspInit()
(++) Encoder mode output : HAL_TIM_Encoder_MspInit()
(#) Initialize the TIM low level resources :
(##) Enable the TIM interface clock using __HAL_RCC_TIMx_CLK_ENABLE();
(##) TIM pins configuration
(+++) Enable the clock for the TIM GPIOs using the following function:
__HAL_RCC_GPIOx_CLK_ENABLE();
(+++) Configure these TIM pins in Alternate function mode using HAL_GPIO_Init();
(#) The external Clock can be configured, if needed (the default clock is the internal clock from the APBx),
using the following function:
HAL_TIM_ConfigClockSource, the clock configuration should be done before any start function.
(#) Configure the TIM in the desired functioning mode using one of the
initialization function of this driver:
(++) HAL_TIM_Base_Init: to use the Timer to generate a simple time base
(++) HAL_TIM_OC_Init and HAL_TIM_OC_ConfigChannel: to use the Timer to generate an
Output Compare signal.
(++) HAL_TIM_PWM_Init and HAL_TIM_PWM_ConfigChannel: to use the Timer to generate a
PWM signal.
(++) HAL_TIM_IC_Init and HAL_TIM_IC_ConfigChannel: to use the Timer to measure an
external signal.
(++) HAL_TIM_OnePulse_Init and HAL_TIM_OnePulse_ConfigChannel: to use the Timer in One Pulse Mode.
(++) HAL_TIM_Encoder_Init: to use the Timer Encoder Interface.
(#) Activate the TIM peripheral using one of the start functions:
HAL_TIM_Base_Start(), HAL_TIM_Base_Start_DMA(), HAL_TIM_Base_Start_IT(),
HAL_TIM_OC_Start(), HAL_TIM_OC_Start_DMA(), HAL_TIM_OC_Start_IT(),
HAL_TIM_IC_Start(), HAL_TIM_IC_Start_DMA(), HAL_TIM_IC_Start_IT(),
HAL_TIM_PWM_Start(), HAL_TIM_PWM_Start_DMA(), HAL_TIM_PWM_Start_IT(),
HAL_TIM_OnePulse_Start(), HAL_TIM_OnePulse_Start_IT(),
HAL_TIM_Encoder_Start(), HAL_TIM_Encoder_Start_DMA() or HAL_TIM_Encoder_Start_IT()
(#) The DMA Burst is managed with the two following functions:
HAL_TIM_DMABurst_WriteStart
HAL_TIM_DMABurst_ReadStart
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32l0xx_hal.h"
/** @addtogroup STM32L0xx_HAL_Driver
* @{
*/
#ifdef HAL_TIM_MODULE_ENABLED
/** @addtogroup TIM
* @brief TIM HAL module driver
* @{
*/
/** @addtogroup TIM_Private
* @{
*/
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
static void TIM_Base_SetConfig(TIM_TypeDef *TIMx, TIM_Base_InitTypeDef *Structure);
static void TIM_OC1_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config);
static void TIM_OC2_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config);
static void TIM_OC3_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config);
static void TIM_OC4_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config);
static void TIM_TI1_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter);
static void TIM_TI1_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter);
static void TIM_TI2_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter);
static void TIM_TI2_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter);
static void TIM_TI3_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter);
static void TIM_TI4_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter);
static void TIM_ETR_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ExtTRGPrescaler, uint32_t TIM_ExtTRGPolarity, uint32_t ExtTRGFilter);
static void TIM_ITRx_SetConfig(TIM_TypeDef* TIMx, uint16_t InputTriggerSource);
static void TIM_CCxChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelState);
static void TIM_DMAPeriodElapsedCplt(DMA_HandleTypeDef *hdma);
static void TIM_DMATriggerCplt(DMA_HandleTypeDef *hdma);
static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef *htim,TIM_SlaveConfigTypeDef * sSlaveConfig);
/**
* @}
*/
/*******************************************************************************/
/* Exported functions ---------------------------------------------------------*/
/*******************************************************************************/
/** @addtogroup TIM_Exported_Functions
* @{
*/
/** @addtogroup TIM_Exported_Functions_Group1
* @brief Time Base functions
*
@verbatim
==============================================================================
##### Timer Base functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the TIM base.
(+) De-initialize the TIM base.
(+) Start the Timer Base.
(+) Stop the Timer Base.
(+) Start the Timer Base and enable interrupt.
(+) Stop the Timer Base and disable interrupt.
(+) Start the Timer Base and enable DMA transfer.
(+) Stop the Timer Base and disable DMA transfer.
@endverbatim
* @{
*/
/**
* @brief Initializes the TIM Time base Unit according to the specified
* parameters in the TIM_HandleTypeDef and create the associated handle.
* @param htim : TIM handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Base_Init(TIM_HandleTypeDef *htim)
{
/* Check the TIM handle allocation */
if(htim == NULL)
{
return HAL_ERROR;
}
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
assert_param(IS_TIM_PERIOD(htim->Init.Period));
assert_param(IS_TIM_PRESCALER(htim->Init.Prescaler));
if(htim->State == HAL_TIM_STATE_RESET)
{
/* Allocate lock resource and initialize it */
htim->Lock = HAL_UNLOCKED;
/* Init the low level hardware : GPIO, CLOCK, NVIC */
HAL_TIM_Base_MspInit(htim);
}
/* Set the TIM state */
htim->State= HAL_TIM_STATE_BUSY;
/* Set the Time Base configuration */
TIM_Base_SetConfig(htim->Instance, &htim->Init);
/* Initialize the TIM state*/
htim->State= HAL_TIM_STATE_READY;
return HAL_OK;
}
/**
* @brief DeInitializes the TIM Base peripheral
* @param htim : TIM handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Base_DeInit(TIM_HandleTypeDef *htim)
{
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
htim->State = HAL_TIM_STATE_BUSY;
/* Disable the TIM Peripheral Clock */
__HAL_TIM_DISABLE(htim);
/* DeInit the low level hardware: GPIO, CLOCK, NVIC */
HAL_TIM_Base_MspDeInit(htim);
/* Change TIM state */
htim->State = HAL_TIM_STATE_RESET;
/* Release Lock */
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Initializes the TIM Base MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_Base_MspInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_Base_MspInit could be implemented in the user file
*/
}
/**
* @brief DeInitializes TIM Base MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_Base_MspDeInit could be implemented in the user file
*/
}
/**
* @brief Starts the TIM Base generation.
* @param htim : TIM handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Base_Start(TIM_HandleTypeDef *htim)
{
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
/* Set the TIM state */
htim->State= HAL_TIM_STATE_BUSY;
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Change the TIM state*/
htim->State= HAL_TIM_STATE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Base generation.
* @param htim : TIM handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Base_Stop(TIM_HandleTypeDef *htim)
{
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
/* Set the TIM state */
htim->State= HAL_TIM_STATE_BUSY;
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Change the TIM state*/
htim->State= HAL_TIM_STATE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @brief Starts the TIM Base generation in interrupt mode.
* @param htim : TIM handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Base_Start_IT(TIM_HandleTypeDef *htim)
{
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
/* Enable the TIM Update interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_UPDATE);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Base generation in interrupt mode.
* @param htim : TIM handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Base_Stop_IT(TIM_HandleTypeDef *htim)
{
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
/* Disable the TIM Update interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_UPDATE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Starts the TIM Base generation in DMA mode.
* @param htim : TIM handle
* @param pData: The source Buffer address.
* @param Length: The length of data to be transferred from memory to peripheral.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Base_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length)
{
/* Check the parameters */
assert_param(IS_TIM_DMA_INSTANCE(htim->Instance));
if((htim->State == HAL_TIM_STATE_BUSY))
{
return HAL_BUSY;
}
else if((htim->State == HAL_TIM_STATE_READY))
{
if((pData == 0U ) && (Length > 0U))
{
return HAL_ERROR;
}
else
{
htim->State = HAL_TIM_STATE_BUSY;
}
}
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)pData, (uint32_t)&htim->Instance->ARR, Length);
/* Enable the TIM Update DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_UPDATE);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Base generation in DMA mode.
* @param htim : TIM handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Base_Stop_DMA(TIM_HandleTypeDef *htim)
{
/* Check the parameters */
assert_param(IS_TIM_DMA_INSTANCE(htim->Instance));
/* Disable the TIM Update DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_UPDATE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Change the htim state */
htim->State = HAL_TIM_STATE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @}
*/
/** @addtogroup TIM_Exported_Functions_Group2
* @brief Time Output Compare functions
*
@verbatim
==============================================================================
##### Timer Output Compare functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the TIM Output Compare.
(+) De-initialize the TIM Output Compare.
(+) Start the Timer Output Compare.
(+) Stop the Timer Output Compare.
(+) Start the Timer Output Compare and enable interrupt.
(+) Stop the Timer Output Compare and disable interrupt.
(+) Start the Timer Output Compare and enable DMA transfer.
(+) Stop the Timer Output Compare and disable DMA transfer.
@endverbatim
* @{
*/
/**
* @brief Initializes the TIM Output Compare according to the specified
* parameters in the TIM_HandleTypeDef and create the associated handle.
* @param htim: TIM Output Compare handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OC_Init(TIM_HandleTypeDef* htim)
{
/* Check the TIM handle allocation */
if(htim == NULL)
{
return HAL_ERROR;
}
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
assert_param(IS_TIM_PERIOD(htim->Init.Period));
assert_param(IS_TIM_PRESCALER(htim->Init.Prescaler));
if(htim->State == HAL_TIM_STATE_RESET)
{
/* Allocate lock resource and initialize it */
htim->Lock = HAL_UNLOCKED;
/* Init the low level hardware : GPIO, CLOCK, NVIC and DMA*/
HAL_TIM_OC_MspInit(htim);
}
/* Set the TIM state */
htim->State= HAL_TIM_STATE_BUSY;
/* Init the base time for the Output Compare */
TIM_Base_SetConfig(htim->Instance, &htim->Init);
/* Initialize the TIM state*/
htim->State= HAL_TIM_STATE_READY;
return HAL_OK;
}
/**
* @brief DeInitializes the TIM peripheral
* @param htim: TIM Output Compare handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OC_DeInit(TIM_HandleTypeDef *htim)
{
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
htim->State = HAL_TIM_STATE_BUSY;
/* Disable the TIM Peripheral Clock */
__HAL_TIM_DISABLE(htim);
/* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */
HAL_TIM_OC_MspDeInit(htim);
/* Change TIM state */
htim->State = HAL_TIM_STATE_RESET;
/* Release Lock */
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Initializes the TIM Output Compare MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_OC_MspInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_OC_MspInit could be implemented in the user file
*/
}
/**
* @brief DeInitializes TIM Output Compare MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_OC_MspDeInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_OC_MspDeInit could be implemented in the user file
*/
}
/**
* @brief Starts the TIM Output Compare signal generation.
* @param htim : TIM handle
* @param Channel: TIM Channel to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OC_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
/* Enable the Output compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Output Compare signal generation.
* @param htim : TIM handle
* @param Channel: TIM Channel to be disabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OC_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
/* Disable the Output compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Starts the TIM Output Compare signal generation in interrupt mode.
* @param htim : TIM handle
* @param Channel: TIM Channel to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OC_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Enable the TIM Capture/Compare 1 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Enable the TIM Capture/Compare 2 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Enable the TIM Capture/Compare 3 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Enable the TIM Capture/Compare 4 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4);
}
break;
default:
break;
}
/* Enable the Output compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Output Compare signal generation in interrupt mode.
* @param htim : TIM handle
* @param Channel: TIM Channel to be disabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OC_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Disable the TIM Capture/Compare 1 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Disable the TIM Capture/Compare 2 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Disable the TIM Capture/Compare 3 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Disable the TIM Capture/Compare 4 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4);
}
break;
default:
break;
}
/* Disable the Output compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Starts the TIM Output Compare signal generation in DMA mode.
* @param htim : TIM handle
* @param Channel: TIM Channel to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @param pData: The source Buffer address.
* @param Length: The length of data to be transferred from memory to TIM peripheral
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OC_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
if((htim->State == HAL_TIM_STATE_BUSY))
{
return HAL_BUSY;
}
else if((htim->State == HAL_TIM_STATE_READY))
{
if(((uint32_t)pData == 0U ) && (Length > 0U))
{
return HAL_ERROR;
}
else
{
htim->State = HAL_TIM_STATE_BUSY;
}
}
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length);
/* Enable the TIM Capture/Compare 1 DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length);
/* Enable the TIM Capture/Compare 2 DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length);
/* Enable the TIM Capture/Compare 3 DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length);
/* Enable the TIM Capture/Compare 4 DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4);
}
break;
default:
break;
}
/* Enable the Output compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Output Compare signal generation in DMA mode.
* @param htim : TIM handle
* @param Channel: TIM Channel to be disabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OC_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Disable the TIM Capture/Compare 1 DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Disable the TIM Capture/Compare 2 DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Disable the TIM Capture/Compare 3 DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Disable the TIM Capture/Compare 4 interrupt */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4);
}
break;
default:
break;
}
/* Disable the Output compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Change the htim state */
htim->State = HAL_TIM_STATE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @}
*/
/** @addtogroup TIM_Exported_Functions_Group3
* @brief Time PWM functions
*
@verbatim
==============================================================================
##### Timer PWM functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the TIM OPWM.
(+) De-initialize the TIM PWM.
(+) Start the Timer PWM.
(+) Stop the Timer PWM.
(+) Start the Timer PWM and enable interrupt.
(+) Stop the Timer PWM and disable interrupt.
(+) Start the Timer PWM and enable DMA transfer.
(+) Stop the Timer PWM and disable DMA transfer.
@endverbatim
* @{
*/
/**
* @brief Initializes the TIM PWM Time Base according to the specified
* parameters in the TIM_HandleTypeDef and create the associated handle.
* @param htim : TIM handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_PWM_Init(TIM_HandleTypeDef *htim)
{
/* Check the TIM handle allocation */
if(htim == NULL)
{
return HAL_ERROR;
}
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
assert_param(IS_TIM_PERIOD(htim->Init.Period));
assert_param(IS_TIM_PRESCALER(htim->Init.Prescaler));
if(htim->State == HAL_TIM_STATE_RESET)
{
/* Allocate lock resource and initialize it */
htim->Lock = HAL_UNLOCKED;
/* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
HAL_TIM_PWM_MspInit(htim);
}
/* Set the TIM state */
htim->State= HAL_TIM_STATE_BUSY;
/* Init the base time for the PWM */
TIM_Base_SetConfig(htim->Instance, &htim->Init);
/* Initialize the TIM state*/
htim->State= HAL_TIM_STATE_READY;
return HAL_OK;
}
/**
* @brief DeInitializes the TIM peripheral
* @param htim : TIM handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_PWM_DeInit(TIM_HandleTypeDef *htim)
{
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
htim->State = HAL_TIM_STATE_BUSY;
/* Disable the TIM Peripheral Clock */
__HAL_TIM_DISABLE(htim);
/* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */
HAL_TIM_PWM_MspDeInit(htim);
/* Change TIM state */
htim->State = HAL_TIM_STATE_RESET;
/* Release Lock */
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Initializes the TIM PWM MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_PWM_MspInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_PWM_MspInit could be implemented in the user file
*/
}
/**
* @brief DeInitializes TIM PWM MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_PWM_MspDeInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_PWM_MspDeInit could be implemented in the user file
*/
}
/**
* @brief Starts the PWM signal generation.
* @param htim : TIM handle
* @param Channel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_PWM_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
/* Enable the Capture compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the PWM signal generation.
* @param htim : TIM handle
* @param Channel: TIM Channels to be disabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_PWM_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
/* Disable the Capture compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Change the htim state */
htim->State = HAL_TIM_STATE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @brief Starts the PWM signal generation in interrupt mode.
* @param htim : TIM handle
* @param Channel: TIM Channel to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_PWM_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Enable the TIM Capture/Compare 1 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Enable the TIM Capture/Compare 2 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Enable the TIM Capture/Compare 3 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Enable the TIM Capture/Compare 4 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4);
}
break;
default:
break;
}
/* Enable the Capture compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the PWM signal generation in interrupt mode.
* @param htim : TIM handle
* @param Channel: TIM Channels to be disabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_PWM_Stop_IT (TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Disable the TIM Capture/Compare 1 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Disable the TIM Capture/Compare 2 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Disable the TIM Capture/Compare 3 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Disable the TIM Capture/Compare 4 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4);
}
break;
default:
break;
}
/* Disable the Capture compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Starts the TIM PWM signal generation in DMA mode.
* @param htim : TIM handle
* @param Channel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @param pData: The source Buffer address. This buffer contains the values
* which will be loaded inside the capture/compare registers.
* @param Length: The length of data to be transferred from memory to TIM peripheral
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_PWM_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
if((htim->State == HAL_TIM_STATE_BUSY))
{
return HAL_BUSY;
}
else if((htim->State == HAL_TIM_STATE_READY))
{
if(((uint32_t)pData == 0U ) && (Length > 0U))
{
return HAL_ERROR;
}
else
{
htim->State = HAL_TIM_STATE_BUSY;
}
}
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length);
/* Enable the TIM Capture/Compare 1 DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length);
/* Enable the TIM Capture/Compare 2 DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length);
/* Enable the TIM Output Capture/Compare 3 request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length);
/* Enable the TIM Capture/Compare 4 DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4);
}
break;
default:
break;
}
/* Enable the Capture compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM PWM signal generation in DMA mode.
* @param htim : TIM handle
* @param Channel: TIM Channels to be disabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_PWM_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Disable the TIM Capture/Compare 1 DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Disable the TIM Capture/Compare 2 DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Disable the TIM Capture/Compare 3 DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Disable the TIM Capture/Compare 4 interrupt */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4);
}
break;
default:
break;
}
/* Disable the Capture compare channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Change the htim state */
htim->State = HAL_TIM_STATE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @}
*/
/** @addtogroup TIM_Exported_Functions_Group4
* @brief Time Input Capture functions
*
@verbatim
==============================================================================
##### Timer Input Capture functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the TIM Input Capture.
(+) De-initialize the TIM Input Capture.
(+) Start the Timer Input Capture.
(+) Stop the Timer Input Capture.
(+) Start the Timer Input Capture and enable interrupt.
(+) Stop the Timer Input Capture and disable interrupt.
(+) Start the Timer Input Capture and enable DMA transfer.
(+) Stop the Timer Input Capture and disable DMA transfer.
@endverbatim
* @{
*/
/**
* @brief Initializes the TIM Input Capture Time base according to the specified
* parameters in the TIM_HandleTypeDef and create the associated handle.
* @param htim: TIM Input Capture handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_IC_Init(TIM_HandleTypeDef *htim)
{
/* Check the TIM handle allocation */
if(htim == NULL)
{
return HAL_ERROR;
}
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
assert_param(IS_TIM_PERIOD(htim->Init.Period));
assert_param(IS_TIM_PRESCALER(htim->Init.Prescaler));
if(htim->State == HAL_TIM_STATE_RESET)
{
/* Allocate lock resource and initialize it */
htim->Lock = HAL_UNLOCKED;
/* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
HAL_TIM_IC_MspInit(htim);
}
/* Set the TIM state */
htim->State= HAL_TIM_STATE_BUSY;
/* Init the base time for the input capture */
TIM_Base_SetConfig(htim->Instance, &htim->Init);
/* Initialize the TIM state*/
htim->State= HAL_TIM_STATE_READY;
return HAL_OK;
}
/**
* @brief DeInitializes the TIM peripheral
* @param htim: TIM Input Capture handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_IC_DeInit(TIM_HandleTypeDef *htim)
{
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
htim->State = HAL_TIM_STATE_BUSY;
/* Disable the TIM Peripheral Clock */
__HAL_TIM_DISABLE(htim);
/* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */
HAL_TIM_IC_MspDeInit(htim);
/* Change TIM state */
htim->State = HAL_TIM_STATE_RESET;
/* Release Lock */
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Initializes the TIM INput Capture MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_IC_MspInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_IC_MspInit could be implemented in the user file
*/
}
/**
* @brief DeInitializes TIM Input Capture MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_IC_MspDeInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_IC_MspDeInit could be implemented in the user file
*/
}
/**
* @brief Starts the TIM Input Capture measurement.
* @param htim : TIM handle
* @param Channel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_IC_Start (TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
/* Enable the Input Capture channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Input Capture measurement.
* @param htim : TIM handle
* @param Channel: TIM Channels to be disabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_IC_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
/* Disable the Input Capture channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Starts the TIM Input Capture measurement in interrupt mode.
* @param htim : TIM handle
* @param Channel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_IC_Start_IT (TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Enable the TIM Capture/Compare 1 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Enable the TIM Capture/Compare 2 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Enable the TIM Capture/Compare 3 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Enable the TIM Capture/Compare 4 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4);
}
break;
default:
break;
}
/* Enable the Input Capture channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Input Capture measurement in interrupt mode.
* @param htim : TIM handle
* @param Channel : TIM Channels to be disabled
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_IC_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Disable the TIM Capture/Compare 1 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Disable the TIM Capture/Compare 2 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Disable the TIM Capture/Compare 3 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Disable the TIM Capture/Compare 4 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4);
}
break;
default:
break;
}
/* Disable the Input Capture channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Starts the TIM Input Capture measurement on in DMA mode.
* @param htim : TIM handle
* @param Channel : TIM Channels to be enabled
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @param pData: The destination Buffer address.
* @param Length: The length of data to be transferred from TIM peripheral to memory.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_IC_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance));
if((htim->State == HAL_TIM_STATE_BUSY))
{
return HAL_BUSY;
}
else if((htim->State == HAL_TIM_STATE_READY))
{
if((pData == 0U ) && (Length > 0U))
{
return HAL_ERROR;
}
else
{
htim->State = HAL_TIM_STATE_BUSY;
}
}
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length);
/* Enable the TIM Capture/Compare 1 DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData, Length);
/* Enable the TIM Capture/Compare 2 DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->CCR3, (uint32_t)pData, Length);
/* Enable the TIM Capture/Compare 3 DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->CCR4, (uint32_t)pData, Length);
/* Enable the TIM Capture/Compare 4 DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4);
}
break;
default:
break;
}
/* Enable the Input Capture channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Input Capture measurement on in DMA mode.
* @param htim : TIM handle
* @param Channel : TIM Channels to be disabled
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_IC_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel));
assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance));
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Disable the TIM Capture/Compare 1 DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
}
break;
case TIM_CHANNEL_2:
{
/* Disable the TIM Capture/Compare 2 DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
}
break;
case TIM_CHANNEL_3:
{
/* Disable the TIM Capture/Compare 3 DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
}
break;
case TIM_CHANNEL_4:
{
/* Disable the TIM Capture/Compare 4 DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4);
}
break;
default:
break;
}
/* Disable the Input Capture channel */
TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Change the htim state */
htim->State = HAL_TIM_STATE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @}
*/
/** @addtogroup TIM_Exported_Functions_Group5
* @brief Time One Pulse functions
*
@verbatim
==============================================================================
##### Timer One Pulse functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the TIM One Pulse.
(+) De-initialize the TIM One Pulse.
(+) Start the Timer One Pulse.
(+) Stop the Timer One Pulse.
(+) Start the Timer One Pulse and enable interrupt.
(+) Stop the Timer One Pulse and disable interrupt.
(+) Start the Timer One Pulse and enable DMA transfer.
(+) Stop the Timer One Pulse and disable DMA transfer.
@endverbatim
* @{
*/
/**
* @brief Initializes the TIM One Pulse Time Base according to the specified
* parameters in the TIM_HandleTypeDef and create the associated handle.
* @param htim: TIM OnePulse handle
* @param OnePulseMode: Select the One pulse mode.
* This parameter can be one of the following values:
* @arg TIM_OPMODE_SINGLE: Only one pulse will be generated.
* @arg TIM_OPMODE_REPETITIVE: Repetitive pulses will be generated.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OnePulse_Init(TIM_HandleTypeDef *htim, uint32_t OnePulseMode)
{
/* Check the TIM handle allocation */
if(htim == NULL)
{
return HAL_ERROR;
}
/* Check the parameters */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
assert_param(IS_TIM_OPM_MODE(OnePulseMode));
assert_param(IS_TIM_PERIOD(htim->Init.Period));
assert_param(IS_TIM_PRESCALER(htim->Init.Prescaler));
if(htim->State == HAL_TIM_STATE_RESET)
{
/* Allocate lock resource and initialize it */
htim->Lock = HAL_UNLOCKED;
/* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
HAL_TIM_OnePulse_MspInit(htim);
}
/* Set the TIM state */
htim->State= HAL_TIM_STATE_BUSY;
/* Configure the Time base in the One Pulse Mode */
TIM_Base_SetConfig(htim->Instance, &htim->Init);
/* Reset the OPM Bit */
htim->Instance->CR1 &= ~TIM_CR1_OPM;
/* Configure the OPM Mode */
htim->Instance->CR1 |= OnePulseMode;
/* Initialize the TIM state*/
htim->State= HAL_TIM_STATE_READY;
return HAL_OK;
}
/**
* @brief DeInitializes the TIM One Pulse
* @param htim: TIM One Pulse handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OnePulse_DeInit(TIM_HandleTypeDef *htim)
{
/* Check the parameters */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
htim->State = HAL_TIM_STATE_BUSY;
/* Disable the TIM Peripheral Clock */
__HAL_TIM_DISABLE(htim);
/* DeInit the low level hardware: GPIO, CLOCK, NVIC */
HAL_TIM_OnePulse_MspDeInit(htim);
/* Change TIM state */
htim->State = HAL_TIM_STATE_RESET;
/* Release Lock */
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Initializes the TIM One Pulse MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_OnePulse_MspInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_OnePulse_MspInit could be implemented in the user file
*/
}
/**
* @brief DeInitializes TIM One Pulse MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_OnePulse_MspDeInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_OnePulse_MspDeInit could be implemented in the user file
*/
}
/**
* @brief Starts the TIM One Pulse signal generation.
* @param htim : TIM handle
* @param OutputChannel : TIM Channels to be enabled.
* This parameter is not used since both channels TIM_CHANNEL_1 and
* TIM_CHANNEL_2 are automatically selected.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OnePulse_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
{
/* Enable the Capture compare and the Input Capture channels
(in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together
No need to enable the counter, it's enabled automatically by hardware
(the counter starts in response to a stimulus and generate a pulse */
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM One Pulse signal generation.
* @param htim : TIM handle
* @param OutputChannel : TIM Channels to be disable.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OnePulse_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
{
/* Disable the Capture compare and the Input Capture channels
(in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Starts the TIM One Pulse signal generation in interrupt mode.
* @param htim : TIM handle
* @param OutputChannel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OnePulse_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
{
/* Enable the Capture compare and the Input Capture channels
(in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together
No need to enable the counter, it's enabled automatically by hardware
(the counter starts in response to a stimulus and generate a pulse */
/* Enable the TIM Capture/Compare 1 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
/* Enable the TIM Capture/Compare 2 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM One Pulse signal generation in interrupt mode.
* @param htim : TIM handle
* @param OutputChannel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OnePulse_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
{
/* Disable the TIM Capture/Compare 1 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
/* Disable the TIM Capture/Compare 2 interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
/* Disable the Capture compare and the Input Capture channels
(in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @}
*/
/** @addtogroup TIM_Exported_Functions_Group6
* @brief Time Encoder functions
*
@verbatim
==============================================================================
##### Timer Encoder functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the TIM Encoder.
(+) De-initialize the TIM Encoder.
(+) Start the Timer Encoder.
(+) Stop the Timer Encoder.
(+) Start the Timer Encoder and enable interrupt.
(+) Stop the Timer Encoder and disable interrupt.
(+) Start the Timer Encoder and enable DMA transfer.
(+) Stop the Timer Encoder and disable DMA transfer.
@endverbatim
* @{
*/
/**
* @brief Initializes the TIM Encoder Interface and create the associated handle.
* @param htim: TIM Encoder Interface handle
* @param sConfig: TIM Encoder Interface configuration structure
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Encoder_Init(TIM_HandleTypeDef *htim, TIM_Encoder_InitTypeDef* sConfig)
{
uint32_t tmpsmcr = 0U;
uint32_t tmpccmr1 = 0U;
uint32_t tmpccer = 0U;
/* Check the TIM handle allocation */
if(htim == NULL)
{
return HAL_ERROR;
}
/* Check the parameters */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
assert_param(IS_TIM_ENCODER_MODE(sConfig->EncoderMode));
assert_param(IS_TIM_IC_SELECTION(sConfig->IC1Selection));
assert_param(IS_TIM_IC_SELECTION(sConfig->IC2Selection));
assert_param(IS_TIM_IC_POLARITY(sConfig->IC1Polarity));
assert_param(IS_TIM_IC_POLARITY(sConfig->IC2Polarity));
assert_param(IS_TIM_IC_PRESCALER(sConfig->IC1Prescaler));
assert_param(IS_TIM_IC_PRESCALER(sConfig->IC2Prescaler));
assert_param(IS_TIM_IC_FILTER(sConfig->IC1Filter));
assert_param(IS_TIM_IC_FILTER(sConfig->IC2Filter));
assert_param(IS_TIM_PERIOD(htim->Init.Period));
assert_param(IS_TIM_PRESCALER(htim->Init.Prescaler));
if(htim->State == HAL_TIM_STATE_RESET)
{
/* Allocate lock resource and initialize it */
htim->Lock = HAL_UNLOCKED;
/* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
HAL_TIM_Encoder_MspInit(htim);
}
/* Set the TIM state */
htim->State= HAL_TIM_STATE_BUSY;
/* Reset the SMS bits */
htim->Instance->SMCR &= ~TIM_SMCR_SMS;
/* Configure the Time base in the Encoder Mode */
TIM_Base_SetConfig(htim->Instance, &htim->Init);
/* Get the TIMx SMCR register value */
tmpsmcr = htim->Instance->SMCR;
/* Get the TIMx CCMR1 register value */
tmpccmr1 = htim->Instance->CCMR1;
/* Get the TIMx CCER register value */
tmpccer = htim->Instance->CCER;
/* Set the encoder Mode */
tmpsmcr |= sConfig->EncoderMode;
/* Select the Capture Compare 1 and the Capture Compare 2 as input */
tmpccmr1 &= ~(TIM_CCMR1_CC1S | TIM_CCMR1_CC2S);
tmpccmr1 |= (sConfig->IC1Selection | (sConfig->IC2Selection << 8U));
/* Set the the Capture Compare 1 and the Capture Compare 2 prescalers and filters */
tmpccmr1 &= ~(TIM_CCMR1_IC1PSC | TIM_CCMR1_IC2PSC);
tmpccmr1 &= ~(TIM_CCMR1_IC1F | TIM_CCMR1_IC2F);
tmpccmr1 |= sConfig->IC1Prescaler | (sConfig->IC2Prescaler << 8U);
tmpccmr1 |= (sConfig->IC1Filter << 4U) | (sConfig->IC2Filter << 12U);
/* Set the TI1 and the TI2 Polarities */
tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC2P);
tmpccer &= ~(TIM_CCER_CC1NP | TIM_CCER_CC2NP);
tmpccer |= sConfig->IC1Polarity | (sConfig->IC2Polarity << 4U);
/* Write to TIMx SMCR */
htim->Instance->SMCR = tmpsmcr;
/* Write to TIMx CCMR1 */
htim->Instance->CCMR1 = tmpccmr1;
/* Write to TIMx CCER */
htim->Instance->CCER = tmpccer;
/* Initialize the TIM state*/
htim->State= HAL_TIM_STATE_READY;
return HAL_OK;
}
/**
* @brief DeInitializes the TIM Encoder interface
* @param htim: TIM Encoder handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Encoder_DeInit(TIM_HandleTypeDef *htim)
{
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
htim->State = HAL_TIM_STATE_BUSY;
/* Disable the TIM Peripheral Clock */
__HAL_TIM_DISABLE(htim);
/* DeInit the low level hardware: GPIO, CLOCK, NVIC */
HAL_TIM_Encoder_MspDeInit(htim);
/* Change TIM state */
htim->State = HAL_TIM_STATE_RESET;
/* Release Lock */
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Initializes the TIM Encoder Interface MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_Encoder_MspInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_Encoder_MspInit could be implemented in the user file
*/
}
/**
* @brief DeInitializes TIM Encoder Interface MSP.
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_Encoder_MspDeInit(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_Encoder_MspDeInit could be implemented in the user file
*/
}
/**
* @brief Starts the TIM Encoder Interface.
* @param htim : TIM handle
* @param Channel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Encoder_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
/* Enable the encoder interface channels */
switch (Channel)
{
case TIM_CHANNEL_1:
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
break;
}
case TIM_CHANNEL_2:
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
break;
}
default :
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
break;
}
}
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Encoder Interface.
* @param htim : TIM handle
* @param Channel: TIM Channels to be disabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Encoder_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
/* Disable the Input Capture channels 1 and 2
(in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */
switch (Channel)
{
case TIM_CHANNEL_1:
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
break;
}
case TIM_CHANNEL_2:
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
break;
}
default :
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
break;
}
}
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Starts the TIM Encoder Interface in interrupt mode.
* @param htim : TIM handle
* @param Channel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Encoder_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
/* Enable the encoder interface channels */
/* Enable the capture compare Interrupts 1 and/or 2 */
switch (Channel)
{
case TIM_CHANNEL_1:
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
break;
}
case TIM_CHANNEL_2:
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
break;
}
default :
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
break;
}
}
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Encoder Interface in interrupt mode.
* @param htim : TIM handle
* @param Channel: TIM Channels to be disabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Encoder_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
/* Disable the Input Capture channels 1 and 2
(in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */
if(Channel == TIM_CHANNEL_1)
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
/* Disable the capture compare Interrupts 1 */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
}
else if(Channel == TIM_CHANNEL_2)
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
/* Disable the capture compare Interrupts 2 */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
}
else
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
/* Disable the capture compare Interrupts 1 and 2 */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
__HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
}
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Change the htim state */
htim->State = HAL_TIM_STATE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @brief Starts the TIM Encoder Interface in DMA mode.
* @param htim : TIM handle
* @param Channel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_ALL : TIM Channel 1 and 2 selected
* @param pData1: The destination Buffer address for IC1.
* @param pData2: The destination Buffer address for IC2.
* @param Length: The length of data to be transferred from TIM peripheral to memory.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Encoder_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData1, uint32_t *pData2, uint16_t Length)
{
/* Check the parameters */
assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance));
if((htim->State == HAL_TIM_STATE_BUSY))
{
return HAL_BUSY;
}
else if((htim->State == HAL_TIM_STATE_READY))
{
if((((pData1 == 0U) || (pData2 == 0U) )) && (Length > 0U))
{
return HAL_ERROR;
}
else
{
htim->State = HAL_TIM_STATE_BUSY;
}
}
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t )pData1, Length);
/* Enable the TIM Input Capture DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Enable the Capture compare channel */
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
}
break;
case TIM_CHANNEL_2:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length);
/* Enable the TIM Input Capture DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Enable the Capture compare channel */
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
}
break;
case TIM_CHANNEL_ALL:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData1, Length);
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length);
/* Enable the Peripheral */
__HAL_TIM_ENABLE(htim);
/* Enable the Capture compare channel */
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE);
/* Enable the TIM Input Capture DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
/* Enable the TIM Input Capture DMA request */
__HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
}
break;
default:
break;
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM Encoder Interface in DMA mode.
* @param htim : TIM handle
* @param Channel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_Encoder_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance));
/* Disable the Input Capture channels 1 and 2
(in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */
if(Channel == TIM_CHANNEL_1)
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
/* Disable the capture compare DMA Request 1 */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
}
else if(Channel == TIM_CHANNEL_2)
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
/* Disable the capture compare DMA Request 2 */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
}
else
{
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
/* Disable the capture compare DMA Request 1 and 2 */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
}
/* Disable the Peripheral */
__HAL_TIM_DISABLE(htim);
/* Change the htim state */
htim->State = HAL_TIM_STATE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @}
*/
/** @addtogroup TIM_Exported_Functions_Group7
* @brief IRQ handler management
*
@verbatim
==============================================================================
##### IRQ handler management #####
==============================================================================
[..]
This section provides Timer IRQ handler function.
@endverbatim
* @{
*/
/**
* @brief This function handles TIM interrupts requests.
* @param htim: TIM handle
* @retval None
*/
void HAL_TIM_IRQHandler(TIM_HandleTypeDef *htim)
{
/* Capture compare 1 event */
if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC1) != RESET)
{
if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC1) !=RESET)
{
{
__HAL_TIM_CLEAR_IT(htim, TIM_IT_CC1);
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1;
/* Input capture event */
if((htim->Instance->CCMR1 & TIM_CCMR1_CC1S) != 0x00U)
{
HAL_TIM_IC_CaptureCallback(htim);
}
/* Output compare event */
else
{
HAL_TIM_OC_DelayElapsedCallback(htim);
HAL_TIM_PWM_PulseFinishedCallback(htim);
}
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
}
}
}
/* Capture compare 2 event */
if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC2) != RESET)
{
if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC2) !=RESET)
{
__HAL_TIM_CLEAR_IT(htim, TIM_IT_CC2);
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2;
/* Input capture event */
if((htim->Instance->CCMR1 & TIM_CCMR1_CC2S) != 0x00U)
{
HAL_TIM_IC_CaptureCallback(htim);
}
/* Output compare event */
else
{
HAL_TIM_OC_DelayElapsedCallback(htim);
HAL_TIM_PWM_PulseFinishedCallback(htim);
}
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
}
}
/* Capture compare 3 event */
if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC3) != RESET)
{
if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC3) !=RESET)
{
__HAL_TIM_CLEAR_IT(htim, TIM_IT_CC3);
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3;
/* Input capture event */
if((htim->Instance->CCMR2 & TIM_CCMR2_CC3S) != 0x00U)
{
HAL_TIM_IC_CaptureCallback(htim);
}
/* Output compare event */
else
{
HAL_TIM_OC_DelayElapsedCallback(htim);
HAL_TIM_PWM_PulseFinishedCallback(htim);
}
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
}
}
/* Capture compare 4 event */
if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC4) != RESET)
{
if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC4) !=RESET)
{
__HAL_TIM_CLEAR_IT(htim, TIM_IT_CC4);
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4;
/* Input capture event */
if((htim->Instance->CCMR2 & TIM_CCMR2_CC4S) != 0x00U)
{
HAL_TIM_IC_CaptureCallback(htim);
}
/* Output compare event */
else
{
HAL_TIM_OC_DelayElapsedCallback(htim);
HAL_TIM_PWM_PulseFinishedCallback(htim);
}
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
}
}
/* TIM Update event */
if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_UPDATE) != RESET)
{
if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_UPDATE) !=RESET)
{
__HAL_TIM_CLEAR_IT(htim, TIM_IT_UPDATE);
HAL_TIM_PeriodElapsedCallback(htim);
}
}
/* TIM Trigger detection event */
if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_TRIGGER) != RESET)
{
if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_TRIGGER) !=RESET)
{
__HAL_TIM_CLEAR_IT(htim, TIM_IT_TRIGGER);
HAL_TIM_TriggerCallback(htim);
}
}
}
/**
* @}
*/
/** @addtogroup TIM_Exported_Functions_Group8
* @brief Peripheral Control functions
*
@verbatim
==============================================================================
##### Peripheral Control functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Configure The Input Output channels for OC, PWM, IC or One Pulse mode.
(+) Configure External Clock source.
(+) Configure Master and the Slave synchronization.
(+) Configure the DMA Burst Mode.
@endverbatim
* @{
*/
/**
* @brief Initializes the TIM Output Compare Channels according to the specified
* parameters in the TIM_OC_InitTypeDef.
* @param htim : TIM handle
* @param sConfig: TIM Output Compare configuration structure
* @param Channel: TIM Channel to be configure.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OC_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CHANNELS(Channel));
assert_param(IS_TIM_OC_MODE(sConfig->OCMode));
assert_param(IS_TIM_OC_POLARITY(sConfig->OCPolarity));
/* Process lock */
__HAL_LOCK(htim);
htim->State = HAL_TIM_STATE_BUSY;
switch (Channel)
{
case TIM_CHANNEL_1:
{
assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
/* Configure the TIM Channel 1 in Output Compare */
TIM_OC1_SetConfig(htim->Instance, sConfig);
}
break;
case TIM_CHANNEL_2:
{
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
/* Configure the TIM Channel 2 in Output Compare */
TIM_OC2_SetConfig(htim->Instance, sConfig);
}
break;
case TIM_CHANNEL_3:
{
assert_param(IS_TIM_CC3_INSTANCE(htim->Instance));
/* Configure the TIM Channel 3 in Output Compare */
TIM_OC3_SetConfig(htim->Instance, sConfig);
}
break;
case TIM_CHANNEL_4:
{
assert_param(IS_TIM_CC4_INSTANCE(htim->Instance));
/* Configure the TIM Channel 4 in Output Compare */
TIM_OC4_SetConfig(htim->Instance, sConfig);
}
break;
default:
break;
}
htim->State = HAL_TIM_STATE_READY;
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Initializes the TIM Input Capture Channels according to the specified
* parameters in the TIM_IC_InitTypeDef.
* @param htim : TIM handle
* @param sConfig: TIM Input Capture configuration structure
* @param Channel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef *htim, TIM_IC_InitTypeDef* sConfig, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
assert_param(IS_TIM_IC_POLARITY(sConfig->ICPolarity));
assert_param(IS_TIM_IC_SELECTION(sConfig->ICSelection));
assert_param(IS_TIM_IC_PRESCALER(sConfig->ICPrescaler));
assert_param(IS_TIM_IC_FILTER(sConfig->ICFilter));
__HAL_LOCK(htim);
htim->State = HAL_TIM_STATE_BUSY;
if (Channel == TIM_CHANNEL_1)
{
/* TI1 Configuration */
TIM_TI1_SetConfig(htim->Instance,
sConfig->ICPolarity,
sConfig->ICSelection,
sConfig->ICFilter);
/* Reset the IC1PSC Bits */
htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC;
/* Set the IC1PSC value */
htim->Instance->CCMR1 |= sConfig->ICPrescaler;
}
else if (Channel == TIM_CHANNEL_2)
{
/* TI2 Configuration */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
TIM_TI2_SetConfig(htim->Instance,
sConfig->ICPolarity,
sConfig->ICSelection,
sConfig->ICFilter);
/* Reset the IC2PSC Bits */
htim->Instance->CCMR1 &= ~TIM_CCMR1_IC2PSC;
/* Set the IC2PSC value */
htim->Instance->CCMR1 |= (sConfig->ICPrescaler << 8U);
}
else if (Channel == TIM_CHANNEL_3)
{
/* TI3 Configuration */
assert_param(IS_TIM_CC3_INSTANCE(htim->Instance));
TIM_TI3_SetConfig(htim->Instance,
sConfig->ICPolarity,
sConfig->ICSelection,
sConfig->ICFilter);
/* Reset the IC3PSC Bits */
htim->Instance->CCMR2 &= ~TIM_CCMR2_IC3PSC;
/* Set the IC3PSC value */
htim->Instance->CCMR2 |= sConfig->ICPrescaler;
}
else
{
/* TI4 Configuration */
assert_param(IS_TIM_CC4_INSTANCE(htim->Instance));
TIM_TI4_SetConfig(htim->Instance,
sConfig->ICPolarity,
sConfig->ICSelection,
sConfig->ICFilter);
/* Reset the IC4PSC Bits */
htim->Instance->CCMR2 &= ~TIM_CCMR2_IC4PSC;
/* Set the IC4PSC value */
htim->Instance->CCMR2 |= (sConfig->ICPrescaler << 8U);
}
htim->State = HAL_TIM_STATE_READY;
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Initializes the TIM PWM channels according to the specified
* parameters in the TIM_OC_InitTypeDef.
* @param htim : TIM handle
* @param sConfig: TIM PWM configuration structure
* @param Channel: TIM Channel to be configured.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_PWM_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel)
{
__HAL_LOCK(htim);
/* Check the parameters */
assert_param(IS_TIM_CHANNELS(Channel));
assert_param(IS_TIM_PWM_MODE(sConfig->OCMode));
assert_param(IS_TIM_OC_POLARITY(sConfig->OCPolarity));
assert_param(IS_TIM_FAST_STATE(sConfig->OCFastMode));
htim->State = HAL_TIM_STATE_BUSY;
switch (Channel)
{
case TIM_CHANNEL_1:
{
assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
/* Configure the Channel 1 in PWM mode */
TIM_OC1_SetConfig(htim->Instance, sConfig);
/* Set the Preload enable bit for channel1 */
htim->Instance->CCMR1 |= TIM_CCMR1_OC1PE;
/* Configure the Output Fast mode */
htim->Instance->CCMR1 &= ~TIM_CCMR1_OC1FE;
htim->Instance->CCMR1 |= sConfig->OCFastMode;
}
break;
case TIM_CHANNEL_2:
{
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
/* Configure the Channel 2 in PWM mode */
TIM_OC2_SetConfig(htim->Instance, sConfig);
/* Set the Preload enable bit for channel2 */
htim->Instance->CCMR1 |= TIM_CCMR1_OC2PE;
/* Configure the Output Fast mode */
htim->Instance->CCMR1 &= ~TIM_CCMR1_OC2FE;
htim->Instance->CCMR1 |= sConfig->OCFastMode << 8U;
}
break;
case TIM_CHANNEL_3:
{
assert_param(IS_TIM_CC3_INSTANCE(htim->Instance));
/* Configure the Channel 3 in PWM mode */
TIM_OC3_SetConfig(htim->Instance, sConfig);
/* Set the Preload enable bit for channel3 */
htim->Instance->CCMR2 |= TIM_CCMR2_OC3PE;
/* Configure the Output Fast mode */
htim->Instance->CCMR2 &= ~TIM_CCMR2_OC3FE;
htim->Instance->CCMR2 |= sConfig->OCFastMode;
}
break;
case TIM_CHANNEL_4:
{
assert_param(IS_TIM_CC4_INSTANCE(htim->Instance));
/* Configure the Channel 4 in PWM mode */
TIM_OC4_SetConfig(htim->Instance, sConfig);
/* Set the Preload enable bit for channel4 */
htim->Instance->CCMR2 |= TIM_CCMR2_OC4PE;
/* Configure the Output Fast mode */
htim->Instance->CCMR2 &= ~TIM_CCMR2_OC4FE;
htim->Instance->CCMR2 |= sConfig->OCFastMode << 8U;
}
break;
default:
break;
}
htim->State = HAL_TIM_STATE_READY;
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Initializes the TIM One Pulse Channels according to the specified
* parameters in the TIM_OnePulse_InitTypeDef.
* @param htim : TIM handle
* @param sConfig: TIM One Pulse configuration structure
* @param OutputChannel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @param InputChannel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OnePulse_InitTypeDef* sConfig, uint32_t OutputChannel, uint32_t InputChannel)
{
TIM_OC_InitTypeDef temp1;
/* Check the parameters */
assert_param(IS_TIM_OPM_CHANNELS(OutputChannel));
assert_param(IS_TIM_OPM_CHANNELS(InputChannel));
if(OutputChannel != InputChannel)
{
__HAL_LOCK(htim);
htim->State = HAL_TIM_STATE_BUSY;
/* Extract the Ouput compare configuration from sConfig structure */
temp1.OCMode = sConfig->OCMode;
temp1.Pulse = sConfig->Pulse;
temp1.OCPolarity = sConfig->OCPolarity;
switch (OutputChannel)
{
case TIM_CHANNEL_1:
{
assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
TIM_OC1_SetConfig(htim->Instance, &temp1);
}
break;
case TIM_CHANNEL_2:
{
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
TIM_OC2_SetConfig(htim->Instance, &temp1);
}
break;
default:
break;
}
switch (InputChannel)
{
case TIM_CHANNEL_1:
{
assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
TIM_TI1_SetConfig(htim->Instance, sConfig->ICPolarity,
sConfig->ICSelection, sConfig->ICFilter);
/* Reset the IC1PSC Bits */
htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC;
/* Select the Trigger source */
htim->Instance->SMCR &= ~TIM_SMCR_TS;
htim->Instance->SMCR |= TIM_TS_TI1FP1;
/* Select the Slave Mode */
htim->Instance->SMCR &= ~TIM_SMCR_SMS;
htim->Instance->SMCR |= TIM_SLAVEMODE_TRIGGER;
}
break;
case TIM_CHANNEL_2:
{
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
TIM_TI2_SetConfig(htim->Instance, sConfig->ICPolarity,
sConfig->ICSelection, sConfig->ICFilter);
/* Reset the IC2PSC Bits */
htim->Instance->CCMR1 &= ~TIM_CCMR1_IC2PSC;
/* Select the Trigger source */
htim->Instance->SMCR &= ~TIM_SMCR_TS;
htim->Instance->SMCR |= TIM_TS_TI2FP2;
/* Select the Slave Mode */
htim->Instance->SMCR &= ~TIM_SMCR_SMS;
htim->Instance->SMCR |= TIM_SLAVEMODE_TRIGGER;
}
break;
default:
break;
}
htim->State = HAL_TIM_STATE_READY;
__HAL_UNLOCK(htim);
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Configure the DMA Burst to transfer Data from the memory to the TIM peripheral
* @param htim : TIM handle
* @param BurstBaseAddress: TIM Base address from when the DMA will starts the Data write.
* This parameters can be on of the following values:
* @arg TIM_DMABASE_CR1
* @arg TIM_DMABASE_CR2
* @arg TIM_DMABASE_SMCR
* @arg TIM_DMABASE_DIER
* @arg TIM_DMABASE_SR
* @arg TIM_DMABASE_EGR
* @arg TIM_DMABASE_CCMR1
* @arg TIM_DMABASE_CCMR2
* @arg TIM_DMABASE_CCER
* @arg TIM_DMABASE_CNT
* @arg TIM_DMABASE_PSC
* @arg TIM_DMABASE_ARR
* @arg TIM_DMABASE_CCR1
* @arg TIM_DMABASE_CCR2
* @arg TIM_DMABASE_CCR3
* @arg TIM_DMABASE_CCR4
* @arg TIM_DMABASE_DCR
* @param BurstRequestSrc: TIM DMA Request sources.
* This parameters can be on of the following values:
* @arg TIM_DMA_UPDATE: TIM update Interrupt source
* @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source
* @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source
* @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source
* @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source
* @arg TIM_DMA_TRIGGER: TIM Trigger DMA source
* @param BurstBuffer: The Buffer address.
* @param BurstLength: DMA Burst length. This parameter can be one value
* between TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS .
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStart(TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc,
uint32_t* BurstBuffer, uint32_t BurstLength)
{
/* Check the parameters */
assert_param(IS_TIM_DMABURST_INSTANCE(htim->Instance));
assert_param(IS_TIM_DMA_BASE(BurstBaseAddress));
assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc));
assert_param(IS_TIM_DMA_LENGTH(BurstLength));
if((htim->State == HAL_TIM_STATE_BUSY))
{
return HAL_BUSY;
}
else if((htim->State == HAL_TIM_STATE_READY))
{
if((BurstBuffer == 0U ) && (BurstLength > 0U))
{
return HAL_ERROR;
}
else
{
htim->State = HAL_TIM_STATE_BUSY;
}
}
switch(BurstRequestSrc)
{
case TIM_DMA_UPDATE:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8) + 1);
}
break;
case TIM_DMA_CC1:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U);
}
break;
case TIM_DMA_CC2:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U);
}
break;
case TIM_DMA_CC3:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U);
}
break;
case TIM_DMA_CC4:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U);
}
break;
case TIM_DMA_TRIGGER:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_TRIGGER]->XferCpltCallback = TIM_DMATriggerCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_TRIGGER]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U);
}
break;
default:
break;
}
/* configure the DMA Burst Mode */
htim->Instance->DCR = BurstBaseAddress | BurstLength;
/* Enable the TIM DMA Request */
__HAL_TIM_ENABLE_DMA(htim, BurstRequestSrc);
htim->State = HAL_TIM_STATE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @brief Stops the TIM DMA Burst mode
* @param htim : TIM handle
* @param BurstRequestSrc: TIM DMA Request sources to disable
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStop(TIM_HandleTypeDef *htim, uint32_t BurstRequestSrc)
{
/* Check the parameters */
assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc));
/* Abort the DMA transfer (at least disable the DMA channel) */
switch(BurstRequestSrc)
{
case TIM_DMA_UPDATE:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_UPDATE]);
}
break;
case TIM_DMA_CC1:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC1]);
}
break;
case TIM_DMA_CC2:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC2]);
}
break;
case TIM_DMA_CC3:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC3]);
}
break;
case TIM_DMA_CC4:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC4]);
}
break;
case TIM_DMA_TRIGGER:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_TRIGGER]);
}
break;
default:
break;
}
/* Disable the TIM Update DMA request */
__HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc);
/* Return function status */
return HAL_OK;
}
/**
* @brief Configure the DMA Burst to transfer Data from the TIM peripheral to the memory
* @param htim : TIM handle
* @param BurstBaseAddress: TIM Base address from when the DMA will starts the Data read.
* This parameters can be on of the following values:
* @arg TIM_DMABASE_CR1
* @arg TIM_DMABASE_CR2
* @arg TIM_DMABASE_SMCR
* @arg TIM_DMABASE_DIER
* @arg TIM_DMABASE_SR
* @arg TIM_DMABASE_EGR
* @arg TIM_DMABASE_CCMR1
* @arg TIM_DMABASE_CCMR2
* @arg TIM_DMABASE_CCER
* @arg TIM_DMABASE_CNT
* @arg TIM_DMABASE_PSC
* @arg TIM_DMABASE_ARR
* @arg TIM_DMABASE_CCR1
* @arg TIM_DMABASE_CCR2
* @arg TIM_DMABASE_CCR3
* @arg TIM_DMABASE_CCR4
* @arg TIM_DMABASE_DCR
* @param BurstRequestSrc: TIM DMA Request sources.
* This parameters can be on of the following values:
* @arg TIM_DMA_UPDATE: TIM update Interrupt source
* @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source
* @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source
* @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source
* @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source
* @arg TIM_DMA_TRIGGER: TIM Trigger DMA source
* @param BurstBuffer: The Buffer address.
* @param BurstLength: DMA Burst length. This parameter can be one value
* between TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS .
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStart(TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc,
uint32_t *BurstBuffer, uint32_t BurstLength)
{
/* Check the parameters */
assert_param(IS_TIM_DMABURST_INSTANCE(htim->Instance));
assert_param(IS_TIM_DMA_BASE(BurstBaseAddress));
assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc));
assert_param(IS_TIM_DMA_LENGTH(BurstLength));
if((htim->State == HAL_TIM_STATE_BUSY))
{
return HAL_BUSY;
}
else if((htim->State == HAL_TIM_STATE_READY))
{
if((BurstBuffer == 0U ) && (BurstLength > 0U))
{
return HAL_ERROR;
}
else
{
htim->State = HAL_TIM_STATE_BUSY;
}
}
switch(BurstRequestSrc)
{
case TIM_DMA_UPDATE:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U);
}
break;
case TIM_DMA_CC1:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U);
}
break;
case TIM_DMA_CC2:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U);
}
break;
case TIM_DMA_CC3:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U);
}
break;
case TIM_DMA_CC4:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMACaptureCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U);
}
break;
case TIM_DMA_TRIGGER:
{
/* Set the DMA Period elapsed callback */
htim->hdma[TIM_DMA_ID_TRIGGER]->XferCpltCallback = TIM_DMATriggerCplt;
/* Set the DMA error callback */
htim->hdma[TIM_DMA_ID_TRIGGER]->XferErrorCallback = TIM_DMAError ;
/* Enable the DMA Stream */
HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U);
}
break;
default:
break;
}
/* configure the DMA Burst Mode */
htim->Instance->DCR = BurstBaseAddress | BurstLength;
/* Enable the TIM DMA Request */
__HAL_TIM_ENABLE_DMA(htim, BurstRequestSrc);
htim->State = HAL_TIM_STATE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @brief Stop the DMA burst reading
* @param htim : TIM handle
* @param BurstRequestSrc: TIM DMA Request sources to disable.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStop(TIM_HandleTypeDef *htim, uint32_t BurstRequestSrc)
{
/* Check the parameters */
assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc));
/* Abort the DMA transfer (at least disable the DMA channel) */
switch(BurstRequestSrc)
{
case TIM_DMA_UPDATE:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_UPDATE]);
}
break;
case TIM_DMA_CC1:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC1]);
}
break;
case TIM_DMA_CC2:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC2]);
}
break;
case TIM_DMA_CC3:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC3]);
}
break;
case TIM_DMA_CC4:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC4]);
}
break;
case TIM_DMA_TRIGGER:
{
HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_TRIGGER]);
}
break;
default:
break;
}
/* Disable the TIM Update DMA request */
__HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc);
/* Return function status */
return HAL_OK;
}
/**
* @brief Generate a software event
* @param htim : TIM handle
* @param EventSource: specifies the event source.
* This parameter can be one of the following values:
* @arg TIM_EventSource_Update: Timer update Event source
* @arg TIM_EVENTSOURCE_CC1: Timer Capture Compare 1 Event source
* @arg TIM_EventSource_CC2: Timer Capture Compare 2 Event source
* @arg TIM_EventSource_CC3: Timer Capture Compare 3 Event source
* @arg TIM_EventSource_CC4: Timer Capture Compare 4 Event source
* @arg TIM_EVENTSOURCE_TRIGGER : Timer Trigger Event source
* @note TIM6 can only generate an update event.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_GenerateEvent(TIM_HandleTypeDef *htim, uint32_t EventSource)
{
/* Check the parameters */
assert_param(IS_TIM_INSTANCE(htim->Instance));
assert_param(IS_TIM_EVENT_SOURCE(EventSource));
/* Process Locked */
__HAL_LOCK(htim);
/* Change the TIM state */
htim->State = HAL_TIM_STATE_BUSY;
/* Set the event sources */
htim->Instance->EGR = EventSource;
/* Change the TIM state */
htim->State = HAL_TIM_STATE_READY;
__HAL_UNLOCK(htim);
/* Return function status */
return HAL_OK;
}
/**
* @brief Configures the OCRef clear feature
* @param htim : TIM handle
* @param sClearInputConfig: pointer to a TIM_ClearInputConfigTypeDef structure that
* contains the OCREF clear feature and parameters for the TIM peripheral.
* @param Channel: specifies the TIM Channel.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_ConfigOCrefClear(TIM_HandleTypeDef *htim, TIM_ClearInputConfigTypeDef * sClearInputConfig, uint32_t Channel)
{
/* Check the parameters */
assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
assert_param(IS_TIM_CHANNELS(Channel));
assert_param(IS_TIM_CLEARINPUT_SOURCE(sClearInputConfig->ClearInputSource));
assert_param(IS_TIM_CLEARINPUT_POLARITY(sClearInputConfig->ClearInputPolarity));
assert_param(IS_TIM_CLEARINPUT_PRESCALER(sClearInputConfig->ClearInputPrescaler));
assert_param(IS_TIM_CLEARINPUT_FILTER(sClearInputConfig->ClearInputFilter));
/* Process Locked */
__HAL_LOCK(htim);
htim->State = HAL_TIM_STATE_BUSY;
if(sClearInputConfig->ClearInputSource == TIM_CLEARINPUTSOURCE_ETR)
{
TIM_ETR_SetConfig(htim->Instance,
sClearInputConfig->ClearInputPrescaler,
sClearInputConfig->ClearInputPolarity,
sClearInputConfig->ClearInputFilter);
/* Set the OCREF clear selection bit */
htim->Instance->SMCR |= TIM_SMCR_OCCS;
}
switch (Channel)
{
case TIM_CHANNEL_1:
{
if(sClearInputConfig->ClearInputState != RESET)
{
/* Enable the Ocref clear feature for Channel 1 */
htim->Instance->CCMR1 |= TIM_CCMR1_OC1CE;
}
else
{
/* Disable the Ocref clear feature for Channel 1 */
htim->Instance->CCMR1 &= ~TIM_CCMR1_OC1CE;
}
}
break;
case TIM_CHANNEL_2:
{
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
if(sClearInputConfig->ClearInputState != RESET)
{
/* Enable the Ocref clear feature for Channel 2 */
htim->Instance->CCMR1 |= TIM_CCMR1_OC2CE;
}
else
{
/* Disable the Ocref clear feature for Channel 2 */
htim->Instance->CCMR1 &= ~TIM_CCMR1_OC2CE;
}
}
break;
case TIM_CHANNEL_3:
{
assert_param(IS_TIM_CC3_INSTANCE(htim->Instance));
if(sClearInputConfig->ClearInputState != RESET)
{
/* Enable the Ocref clear feature for Channel 3 */
htim->Instance->CCMR2 |= TIM_CCMR2_OC3CE;
}
else
{
/* Disable the Ocref clear feature for Channel 3 */
htim->Instance->CCMR2 &= ~TIM_CCMR2_OC3CE;
}
}
break;
case TIM_CHANNEL_4:
{
assert_param(IS_TIM_CC4_INSTANCE(htim->Instance));
if(sClearInputConfig->ClearInputState != RESET)
{
/* Enable the Ocref clear feature for Channel 4 */
htim->Instance->CCMR2 |= TIM_CCMR2_OC4CE;
}
else
{
/* Disable the Ocref clear feature for Channel 4 */
htim->Instance->CCMR2 &= ~TIM_CCMR2_OC4CE;
}
}
break;
default:
break;
}
htim->State = HAL_TIM_STATE_READY;
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Configures the clock source to be used
* @param htim : TIM handle
* @param sClockSourceConfig: pointer to a TIM_ClockConfigTypeDef structure that
* contains the clock source information for the TIM peripheral.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_ConfigClockSource(TIM_HandleTypeDef *htim, TIM_ClockConfigTypeDef * sClockSourceConfig)
{
uint32_t tmpsmcr = 0U;
/* Process Locked */
__HAL_LOCK(htim);
htim->State = HAL_TIM_STATE_BUSY;
/* Check the clock source */
assert_param(IS_TIM_CLOCKSOURCE(sClockSourceConfig->ClockSource));
/* Reset the SMS, TS, ECE, ETPS and ETRF bits */
tmpsmcr = htim->Instance->SMCR;
tmpsmcr &= ~(TIM_SMCR_SMS | TIM_SMCR_TS);
tmpsmcr &= ~(TIM_SMCR_ETF | TIM_SMCR_ETPS | TIM_SMCR_ECE | TIM_SMCR_ETP);
htim->Instance->SMCR = tmpsmcr;
switch (sClockSourceConfig->ClockSource)
{
case TIM_CLOCKSOURCE_INTERNAL:
{
assert_param(IS_TIM_INSTANCE(htim->Instance));
/* Disable slave mode to clock the prescaler directly with the internal clock */
htim->Instance->SMCR &= ~TIM_SMCR_SMS;
}
break;
case TIM_CLOCKSOURCE_ETRMODE1:
{
assert_param(IS_TIM_ETR_INSTANCE(htim->Instance));
assert_param(IS_TIM_CLOCKPRESCALER(sClockSourceConfig->ClockPrescaler));
assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity));
assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter));
/* Configure the ETR Clock source */
TIM_ETR_SetConfig(htim->Instance,
sClockSourceConfig->ClockPrescaler,
sClockSourceConfig->ClockPolarity,
sClockSourceConfig->ClockFilter);
/* Get the TIMx SMCR register value */
tmpsmcr = htim->Instance->SMCR;
/* Reset the SMS and TS Bits */
tmpsmcr &= ~(TIM_SMCR_SMS | TIM_SMCR_TS);
/* Select the External clock mode1 and the ETRF trigger */
tmpsmcr |= (TIM_SLAVEMODE_EXTERNAL1 | TIM_CLOCKSOURCE_ETRMODE1);
/* Write to TIMx SMCR */
htim->Instance->SMCR = tmpsmcr;
}
break;
case TIM_CLOCKSOURCE_ETRMODE2:
{
assert_param(IS_TIM_ETR_INSTANCE(htim->Instance));
assert_param(IS_TIM_CLOCKPRESCALER(sClockSourceConfig->ClockPrescaler));
assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity));
assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter));
/* Configure the ETR Clock source */
TIM_ETR_SetConfig(htim->Instance,
sClockSourceConfig->ClockPrescaler,
sClockSourceConfig->ClockPolarity,
sClockSourceConfig->ClockFilter);
/* Enable the External clock mode2 */
htim->Instance->SMCR |= TIM_SMCR_ECE;
}
break;
case TIM_CLOCKSOURCE_TI1:
{
assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity));
assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter));
TIM_TI1_ConfigInputStage(htim->Instance,
sClockSourceConfig->ClockPolarity,
sClockSourceConfig->ClockFilter);
TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI1);
}
break;
case TIM_CLOCKSOURCE_TI2:
{
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity));
assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter));
TIM_TI2_ConfigInputStage(htim->Instance,
sClockSourceConfig->ClockPolarity,
sClockSourceConfig->ClockFilter);
TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI2);
}
break;
case TIM_CLOCKSOURCE_TI1ED:
{
assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity));
assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter));
TIM_TI1_ConfigInputStage(htim->Instance,
sClockSourceConfig->ClockPolarity,
sClockSourceConfig->ClockFilter);
TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI1ED);
}
break;
case TIM_CLOCKSOURCE_ITR0:
{
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR0);
}
break;
case TIM_CLOCKSOURCE_ITR1:
{
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR1);
}
break;
case TIM_CLOCKSOURCE_ITR2:
{
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR2);
}
break;
case TIM_CLOCKSOURCE_ITR3:
{
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR3);
}
break;
default:
break;
}
htim->State = HAL_TIM_STATE_READY;
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Selects the signal connected to the TI1 input: direct from CH1_input
* or a XOR combination between CH1_input, CH2_input & CH3_input
* @param htim : TIM handle
* @param TI1_Selection: Indicate whether or not channel 1 is connected to the
* output of a XOR gate.
* This parameter can be one of the following values:
* @arg TIM_TI1SELECTION_CH1: The TIMx_CH1 pin is connected to TI1 input
* @arg TIM_TI1SELECTION_XORCOMBINATION: The TIMx_CH1, CH2 and CH3
* pins are connected to the TI1 input (XOR combination)
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_ConfigTI1Input(TIM_HandleTypeDef *htim, uint32_t TI1_Selection)
{
uint32_t tmpcr2 = 0U;
/* Check the parameters */
assert_param(IS_TIM_XOR_INSTANCE(htim->Instance));
assert_param(IS_TIM_TI1SELECTION(TI1_Selection));
/* Get the TIMx CR2 register value */
tmpcr2 = htim->Instance->CR2;
/* Reset the TI1 selection */
tmpcr2 &= ~TIM_CR2_TI1S;
/* Set the the TI1 selection */
tmpcr2 |= TI1_Selection;
/* Write to TIMxCR2 */
htim->Instance->CR2 = tmpcr2;
return HAL_OK;
}
/**
* @brief Configures the TIM in Slave mode
* @param htim : TIM handle
* @param sSlaveConfig: pointer to a TIM_SlaveConfigTypeDef structure that
* contains the selected trigger (internal trigger input, filtered
* timer input or external trigger input) and the ) and the Slave
* mode (Disable, Reset, Gated, Trigger, External clock mode 1).
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization(TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef * sSlaveConfig)
{
/* Check the parameters */
assert_param(IS_TIM_SLAVE_INSTANCE(htim->Instance));
assert_param(IS_TIM_SLAVE_MODE(sSlaveConfig->SlaveMode));
assert_param(IS_TIM_TRIGGER_SELECTION(sSlaveConfig->InputTrigger));
__HAL_LOCK(htim);
htim->State = HAL_TIM_STATE_BUSY;
/* Configuration in slave mode */
TIM_SlaveTimer_SetConfig(htim, sSlaveConfig);
/* Disable Trigger Interrupt */
__HAL_TIM_DISABLE_IT(htim, TIM_IT_TRIGGER);
/* Disable Trigger DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_TRIGGER);
/* Set the new state */
htim->State = HAL_TIM_STATE_READY;
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Configures the TIM in Slave mode in interrupt mode
* @param htim : TIM handle.
* @param sSlaveConfig: pointer to a TIM_SlaveConfigTypeDef structure that
* contains the selected trigger (internal trigger input, filtered
* timer input or external trigger input) and the ) and the Slave
* mode (Disable, Reset, Gated, Trigger, External clock mode 1).
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization_IT(TIM_HandleTypeDef *htim,
TIM_SlaveConfigTypeDef * sSlaveConfig)
{
/* Check the parameters */
assert_param(IS_TIM_SLAVE_INSTANCE(htim->Instance));
assert_param(IS_TIM_SLAVE_MODE(sSlaveConfig->SlaveMode));
assert_param(IS_TIM_TRIGGER_SELECTION(sSlaveConfig->InputTrigger));
__HAL_LOCK(htim);
htim->State = HAL_TIM_STATE_BUSY;
TIM_SlaveTimer_SetConfig(htim, sSlaveConfig);
/* Enable Trigger Interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_TRIGGER);
/* Disable Trigger DMA request */
__HAL_TIM_DISABLE_DMA(htim, TIM_DMA_TRIGGER);
htim->State = HAL_TIM_STATE_READY;
__HAL_UNLOCK(htim);
return HAL_OK;
}
/**
* @brief Read the captured value from Capture Compare unit
* @param htim : TIM handle
* @param Channel: TIM Channels to be enabled.
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
* @arg TIM_CHANNEL_3: TIM Channel 3 selected
* @arg TIM_CHANNEL_4: TIM Channel 4 selected
* @retval Captured value
*/
uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef *htim, uint32_t Channel)
{
uint32_t tmpreg = 0U;
__HAL_LOCK(htim);
switch (Channel)
{
case TIM_CHANNEL_1:
{
/* Check the parameters */
assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
/* Return the capture 1 value */
tmpreg = htim->Instance->CCR1;
break;
}
case TIM_CHANNEL_2:
{
/* Check the parameters */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
/* Return the capture 2 value */
tmpreg = htim->Instance->CCR2;
break;
}
case TIM_CHANNEL_3:
{
/* Check the parameters */
assert_param(IS_TIM_CC3_INSTANCE(htim->Instance));
/* Return the capture 3 value */
tmpreg = htim->Instance->CCR3;
break;
}
case TIM_CHANNEL_4:
{
/* Check the parameters */
assert_param(IS_TIM_CC4_INSTANCE(htim->Instance));
/* Return the capture 4 value */
tmpreg = htim->Instance->CCR4;
break;
}
default:
break;
}
__HAL_UNLOCK(htim);
return tmpreg;
}
/**
* @}
*/
/** @addtogroup TIM_Exported_Functions_Group9
* @brief TIM Callbacks functions
*
@verbatim
==============================================================================
##### TIM Callbacks functions #####
==============================================================================
[..]
This section provides TIM callback functions:
(+) Timer Period elapsed callback
(+) Timer Output Compare callback
(+) Timer Input capture callback
(+) Timer Trigger callback
(+) Timer Error callback
@endverbatim
* @{
*/
/**
* @brief Period elapsed callback in non blocking mode
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the __HAL_TIM_PeriodElapsedCallback could be implemented in the user file
*/
}
/**
* @brief Output Compare callback in non blocking mode
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_OC_DelayElapsedCallback(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the __HAL_TIM_OC_DelayElapsedCallback could be implemented in the user file
*/
}
/**
* @brief Input Capture callback in non blocking mode
* @param htim: TIM IC handle
* @retval None
*/
__weak void HAL_TIM_IC_CaptureCallback(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the __HAL_TIM_IC_CaptureCallback could be implemented in the user file
*/
}
/**
* @brief PWM Pulse finished callback in non blocking mode
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_PWM_PulseFinishedCallback(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the __HAL_TIM_PWM_PulseFinishedCallback could be implemented in the user file
*/
}
/**
* @brief Hall Trigger detection callback in non blocking mode
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_TriggerCallback(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_TriggerCallback could be implemented in the user file
*/
}
/**
* @brief Timer error callback in non blocking mode
* @param htim : TIM handle
* @retval None
*/
__weak void HAL_TIM_ErrorCallback(TIM_HandleTypeDef *htim)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(htim);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_TIM_ErrorCallback could be implemented in the user file
*/
}
/**
* @}
*/
/** @addtogroup TIM_Exported_Functions_Group10
* @brief Peripheral State functions
*
@verbatim
==============================================================================
##### Peripheral State functions #####
==============================================================================
[..]
This subsection permits to get in run-time the status of the peripheral
and the data flow.
@endverbatim
* @{
*/
/**
* @brief Return the TIM Base state
* @param htim : TIM handle
* @retval HAL state
*/
HAL_TIM_StateTypeDef HAL_TIM_Base_GetState(TIM_HandleTypeDef *htim)
{
return htim->State;
}
/**
* @brief Return the TIM OC state
* @param htim: TIM Ouput Compare handle
* @retval HAL state
*/
HAL_TIM_StateTypeDef HAL_TIM_OC_GetState(TIM_HandleTypeDef *htim)
{
return htim->State;
}
/**
* @brief Return the TIM PWM state
* @param htim : TIM handle
* @retval HAL state
*/
HAL_TIM_StateTypeDef HAL_TIM_PWM_GetState(TIM_HandleTypeDef *htim)
{
return htim->State;
}
/**
* @brief Return the TIM Input Capture state
* @param htim : TIM handle
* @retval HAL state
*/
HAL_TIM_StateTypeDef HAL_TIM_IC_GetState(TIM_HandleTypeDef *htim)
{
return htim->State;
}
/**
* @brief Return the TIM One Pulse Mode state
* @param htim: TIM OPM handle
* @retval HAL state
*/
HAL_TIM_StateTypeDef HAL_TIM_OnePulse_GetState(TIM_HandleTypeDef *htim)
{
return htim->State;
}
/**
* @brief Return the TIM Encoder Mode state
* @param htim : TIM handle
* @retval HAL state
*/
HAL_TIM_StateTypeDef HAL_TIM_Encoder_GetState(TIM_HandleTypeDef *htim)
{
return htim->State;
}
/**
* @brief TIM DMA error callback
* @param hdma: pointer to a DMA_HandleTypeDef structure that contains
* the configuration information for the specified DMA module.
* @retval None
*/
void TIM_DMAError(DMA_HandleTypeDef *hdma)
{
TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
htim->State= HAL_TIM_STATE_READY;
HAL_TIM_ErrorCallback(htim);
}
/**
* @brief TIM DMA Delay Pulse complete callback.
* @param hdma : pointer to a DMA_HandleTypeDef structure that contains
* the configuration information for the specified DMA module.
* @retval None
*/
void TIM_DMADelayPulseCplt(DMA_HandleTypeDef *hdma)
{
TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
htim->State= HAL_TIM_STATE_READY;
if (hdma == htim->hdma[TIM_DMA_ID_CC1])
{
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1;
}
else if (hdma == htim->hdma[TIM_DMA_ID_CC2])
{
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2;
}
else if (hdma == htim->hdma[TIM_DMA_ID_CC3])
{
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3;
}
else if (hdma == htim->hdma[TIM_DMA_ID_CC4])
{
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4;
}
HAL_TIM_PWM_PulseFinishedCallback(htim);
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
}
/**
* @brief TIM DMA Capture complete callback.
* @param hdma : pointer to a DMA_HandleTypeDef structure that contains
* the configuration information for the specified DMA module.
* @retval None
*/
void TIM_DMACaptureCplt(DMA_HandleTypeDef *hdma)
{
TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
htim->State= HAL_TIM_STATE_READY;
if (hdma == htim->hdma[TIM_DMA_ID_CC1])
{
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1;
}
else if (hdma == htim->hdma[TIM_DMA_ID_CC2])
{
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2;
}
else if (hdma == htim->hdma[TIM_DMA_ID_CC3])
{
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3;
}
else if (hdma == htim->hdma[TIM_DMA_ID_CC4])
{
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4;
}
HAL_TIM_IC_CaptureCallback(htim);
htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED;
}
/**
* @}
*/
/**
* @}
*/
/*************************************************************/
/* Private functions */
/*************************************************************/
/** @addtogroup TIM_Private TIM Private
* @{
*/
/**
* @brief TIM DMA Period Elapse complete callback.
* @param hdma : pointer to DMA handle.
* @retval None
*/
static void TIM_DMAPeriodElapsedCplt(DMA_HandleTypeDef *hdma)
{
TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
htim->State= HAL_TIM_STATE_READY;
HAL_TIM_PeriodElapsedCallback(htim);
}
/**
* @brief TIM DMA Trigger callback.
* @param hdma : pointer to DMA handle.
* @retval None
*/
static void TIM_DMATriggerCplt(DMA_HandleTypeDef *hdma)
{
TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
htim->State= HAL_TIM_STATE_READY;
HAL_TIM_TriggerCallback(htim);
}
/**
* @brief Time Base configuration
* @param TIMx : TIM peripheral
* @param Structure : TIM Base configuration structure
* @retval None
*/
static void TIM_Base_SetConfig(TIM_TypeDef *TIMx, TIM_Base_InitTypeDef *Structure)
{
uint32_t tmpcr1 = 0U;
tmpcr1 = TIMx->CR1;
/* Set TIM Time Base Unit parameters ---------------------------------------*/
if(IS_TIM_CC1_INSTANCE(TIMx) != RESET)
{
/* Select the Counter Mode */
tmpcr1 &= ~(TIM_CR1_DIR | TIM_CR1_CMS);
tmpcr1 |= Structure->CounterMode;
}
if(IS_TIM_CC1_INSTANCE(TIMx) != RESET)
{
/* Set the clock division */
tmpcr1 &= ~TIM_CR1_CKD;
tmpcr1 |= (uint32_t)Structure->ClockDivision;
}
TIMx->CR1 = tmpcr1;
/* Set the Autoreload value */
TIMx->ARR = (uint32_t)Structure->Period ;
/* Set the Prescaler value */
TIMx->PSC = (uint32_t)Structure->Prescaler;
/* Generate an update event to reload the Prescaler value immediatly */
TIMx->EGR = TIM_EGR_UG;
}
/**
* @brief Time Ouput Compare 1 configuration
* @param TIMx to select the TIM peripheral
* @param OC_Config: The ouput configuration structure
* @retval None
*/
static void TIM_OC1_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config)
{
uint32_t tmpccmrx = 0U;
uint32_t tmpccer = 0U;
uint32_t tmpcr2 = 0U;
/* Disable the Channel 1: Reset the CC1E Bit */
TIMx->CCER &= ~TIM_CCER_CC1E;
/* Get the TIMx CCER register value */
tmpccer = TIMx->CCER;
/* Get the TIMx CR2 register value */
tmpcr2 = TIMx->CR2;
/* Get the TIMx CCMR1 register value */
tmpccmrx = TIMx->CCMR1;
/* Reset the Output Compare Mode Bits */
tmpccmrx &= ~TIM_CCMR1_OC1M;
tmpccmrx &= ~TIM_CCMR1_CC1S;
/* Select the Output Compare Mode */
tmpccmrx |= OC_Config->OCMode;
/* Reset the Output Polarity level */
tmpccer &= ~TIM_CCER_CC1P;
/* Set the Output Compare Polarity */
tmpccer |= OC_Config->OCPolarity;
/* Write to TIMx CR2 */
TIMx->CR2 = tmpcr2;
/* Write to TIMx CCMR1 */
TIMx->CCMR1 = tmpccmrx;
/* Set the Capture Compare Register value */
TIMx->CCR1 = OC_Config->Pulse;
/* Write to TIMx CCER */
TIMx->CCER = tmpccer;
}
/**
* @brief Time Ouput Compare 2 configuration
* @param TIMx to select the TIM peripheral
* @param OC_Config: The ouput configuration structure
* @retval None
*/
static void TIM_OC2_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config)
{
uint32_t tmpccmrx = 0U;
uint32_t tmpccer = 0U;
uint32_t tmpcr2 = 0U;
/* Disable the Channel 2: Reset the CC2E Bit */
TIMx->CCER &= ~TIM_CCER_CC2E;
/* Get the TIMx CCER register value */
tmpccer = TIMx->CCER;
/* Get the TIMx CR2 register value */
tmpcr2 = TIMx->CR2;
/* Get the TIMx CCMR1 register value */
tmpccmrx = TIMx->CCMR1;
/* Reset the Output Compare mode and Capture/Compare selection Bits */
tmpccmrx &= ~TIM_CCMR1_OC2M;
tmpccmrx &= ~TIM_CCMR1_CC2S;
/* Select the Output Compare Mode */
tmpccmrx |= (OC_Config->OCMode << 8U);
/* Reset the Output Polarity level */
tmpccer &= ~TIM_CCER_CC2P;
/* Set the Output Compare Polarity */
tmpccer |= (OC_Config->OCPolarity << 4U);
/* Write to TIMx CR2 */
TIMx->CR2 = tmpcr2;
/* Write to TIMx CCMR1 */
TIMx->CCMR1 = tmpccmrx;
/* Set the Capture Compare Register value */
TIMx->CCR2 = OC_Config->Pulse;
/* Write to TIMx CCER */
TIMx->CCER = tmpccer;
}
/**
* @brief Time Ouput Compare 3 configuration
* @param TIMx to select the TIM peripheral
* @param OC_Config: The ouput configuration structure
* @retval None
*/
static void TIM_OC3_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config)
{
uint32_t tmpccmrx = 0U;
uint32_t tmpccer = 0U;
uint32_t tmpcr2 = 0U;
/* Disable the Channel 3: Reset the CC2E Bit */
TIMx->CCER &= ~TIM_CCER_CC3E;
/* Get the TIMx CCER register value */
tmpccer = TIMx->CCER;
/* Get the TIMx CR2 register value */
tmpcr2 = TIMx->CR2;
/* Get the TIMx CCMR2 register value */
tmpccmrx = TIMx->CCMR2;
/* Reset the Output Compare mode and Capture/Compare selection Bits */
tmpccmrx &= ~TIM_CCMR2_OC3M;
tmpccmrx &= ~TIM_CCMR2_CC3S;
/* Select the Output Compare Mode */
tmpccmrx |= OC_Config->OCMode;
/* Reset the Output Polarity level */
tmpccer &= ~TIM_CCER_CC3P;
/* Set the Output Compare Polarity */
tmpccer |= (OC_Config->OCPolarity << 8U);
/* Write to TIMx CR2 */
TIMx->CR2 = tmpcr2;
/* Write to TIMx CCMR2 */
TIMx->CCMR2 = tmpccmrx;
/* Set the Capture Compare Register value */
TIMx->CCR3 = OC_Config->Pulse;
/* Write to TIMx CCER */
TIMx->CCER = tmpccer;
}
/**
* @brief Time Ouput Compare 4 configuration
* @param TIMx to select the TIM peripheral
* @param OC_Config: The ouput configuration structure
* @retval None
*/
static void TIM_OC4_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config)
{
uint32_t tmpccmrx = 0U;
uint32_t tmpccer = 0U;
uint32_t tmpcr2 = 0U;
/* Disable the Channel 4: Reset the CC4E Bit */
TIMx->CCER &= ~TIM_CCER_CC4E;
/* Get the TIMx CCER register value */
tmpccer = TIMx->CCER;
/* Get the TIMx CR2 register value */
tmpcr2 = TIMx->CR2;
/* Get the TIMx CCMR2 register value */
tmpccmrx = TIMx->CCMR2;
/* Reset the Output Compare mode and Capture/Compare selection Bits */
tmpccmrx &= ~TIM_CCMR2_OC4M;
tmpccmrx &= ~TIM_CCMR2_CC4S;
/* Select the Output Compare Mode */
tmpccmrx |= (OC_Config->OCMode << 8U);
/* Reset the Output Polarity level */
tmpccer &= ~TIM_CCER_CC4P;
/* Set the Output Compare Polarity */
tmpccer |= (OC_Config->OCPolarity << 12U);
/* Write to TIMx CR2 */
TIMx->CR2 = tmpcr2;
/* Write to TIMx CCMR2 */
TIMx->CCMR2 = tmpccmrx;
/* Set the Capture Compare Register value */
TIMx->CCR4 = OC_Config->Pulse;
/* Write to TIMx CCER */
TIMx->CCER = tmpccer;
}
/**
* @brief Configure the TI1 as Input.
* @param TIMx to select the TIM peripheral.
* @param TIM_ICPolarity : The Input Polarity.
* This parameter can be one of the following values:
* @arg TIM_ICPolarity_Rising
* @arg TIM_ICPolarity_Falling
* @arg TIM_ICPolarity_BothEdge
* @param TIM_ICSelection: specifies the input to be used.
* This parameter can be one of the following values:
* @arg TIM_ICSelection_DirectTI: TIM Input 1 is selected to be connected to IC1.
* @arg TIM_ICSelection_IndirectTI: TIM Input 1 is selected to be connected to IC2.
* @arg TIM_ICSelection_TRC: TIM Input 1 is selected to be connected to TRC.
* @param TIM_ICFilter: Specifies the Input Capture Filter.
* This parameter must be a value between 0x00 and 0x0F.
* @retval None
*/
static void TIM_TI1_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection,
uint32_t TIM_ICFilter)
{
uint32_t tmpccmr1 = 0U;
uint32_t tmpccer = 0U;
/* Disable the Channel 1: Reset the CC1E Bit */
TIMx->CCER &= ~TIM_CCER_CC1E;
tmpccmr1 = TIMx->CCMR1;
tmpccer = TIMx->CCER;
/* Select the Input */
if(IS_TIM_CC2_INSTANCE(TIMx) != RESET)
{
tmpccmr1 &= ~TIM_CCMR1_CC1S;
tmpccmr1 |= TIM_ICSelection;
}
else
{
tmpccmr1 &= ~TIM_CCMR1_CC1S;
tmpccmr1 |= TIM_CCMR1_CC1S_0;
}
/* Set the filter */
tmpccmr1 &= ~TIM_CCMR1_IC1F;
tmpccmr1 |= ((TIM_ICFilter << 4U) & TIM_CCMR1_IC1F);
/* Select the Polarity and set the CC1E Bit */
tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP);
tmpccer |= (TIM_ICPolarity & (TIM_CCER_CC1P | TIM_CCER_CC1NP));
/* Write to TIMx CCMR1 and CCER registers */
TIMx->CCMR1 = tmpccmr1;
TIMx->CCER = tmpccer;
}
/**
* @brief Configure the Polarity and Filter for TI1.
* @param TIMx to select the TIM peripheral.
* @param TIM_ICPolarity : The Input Polarity.
* This parameter can be one of the following values:
* @arg TIM_ICPolarity_Rising
* @arg TIM_ICPolarity_Falling
* @arg TIM_ICPolarity_BothEdge
* @param TIM_ICFilter: Specifies the Input Capture Filter.
* This parameter must be a value between 0x00 and 0x0F.
* @retval None
*/
static void TIM_TI1_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter)
{
uint32_t tmpccmr1 = 0U;
uint32_t tmpccer = 0U;
/* Disable the Channel 1: Reset the CC1E Bit */
tmpccer = TIMx->CCER;
TIMx->CCER &= ~TIM_CCER_CC1E;
tmpccmr1 = TIMx->CCMR1;
/* Set the filter */
tmpccmr1 &= ~TIM_CCMR1_IC1F;
tmpccmr1 |= (TIM_ICFilter << 4U);
/* Select the Polarity and set the CC1E Bit */
tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP);
tmpccer |= TIM_ICPolarity;
/* Write to TIMx CCMR1 and CCER registers */
TIMx->CCMR1 = tmpccmr1;
TIMx->CCER = tmpccer;
}
/**
* @brief Configure the TI2 as Input.
* @param TIMx to select the TIM peripheral
* @param TIM_ICPolarity : The Input Polarity.
* This parameter can be one of the following values:
* @arg TIM_ICPolarity_Rising
* @arg TIM_ICPolarity_Falling
* @arg TIM_ICPolarity_BothEdge
* @param TIM_ICSelection: specifies the input to be used.
* This parameter can be one of the following values:
* @arg TIM_ICSelection_DirectTI: TIM Input 2 is selected to be connected to IC2.
* @arg TIM_ICSelection_IndirectTI: TIM Input 2 is selected to be connected to IC1.
* @arg TIM_ICSelection_TRC: TIM Input 2 is selected to be connected to TRC.
* @param TIM_ICFilter: Specifies the Input Capture Filter.
* This parameter must be a value between 0x00 and 0x0F.
* @retval None
*/
static void TIM_TI2_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection,
uint32_t TIM_ICFilter)
{
uint32_t tmpccmr1 = 0U;
uint32_t tmpccer = 0U;
/* Disable the Channel 2: Reset the CC2E Bit */
TIMx->CCER &= ~TIM_CCER_CC2E;
tmpccmr1 = TIMx->CCMR1;
tmpccer = TIMx->CCER;
/* Select the Input */
tmpccmr1 &= ~TIM_CCMR1_CC2S;
tmpccmr1 |= (TIM_ICSelection << 8U);
/* Set the filter */
tmpccmr1 &= ~TIM_CCMR1_IC2F;
tmpccmr1 |= ((TIM_ICFilter << 12U) & TIM_CCMR1_IC2F);
/* Select the Polarity and set the CC2E Bit */
tmpccer &= ~(TIM_CCER_CC2P | TIM_CCER_CC2NP);
tmpccer |= ((TIM_ICPolarity << 4U) & (TIM_CCER_CC2P | TIM_CCER_CC2NP));
/* Write to TIMx CCMR1 and CCER registers */
TIMx->CCMR1 = tmpccmr1 ;
TIMx->CCER = tmpccer;
}
/**
* @brief Configure the Polarity and Filter for TI2.
* @param TIMx to select the TIM peripheral.
* @param TIM_ICPolarity : The Input Polarity.
* This parameter can be one of the following values:
* @arg TIM_ICPolarity_Rising
* @arg TIM_ICPolarity_Falling
* @arg TIM_ICPolarity_BothEdge
* @param TIM_ICFilter: Specifies the Input Capture Filter.
* This parameter must be a value between 0x00 and 0x0F.
* @retval None
*/
static void TIM_TI2_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter)
{
uint32_t tmpccmr1 = 0U;
uint32_t tmpccer = 0U;
/* Disable the Channel 2: Reset the CC2E Bit */
TIMx->CCER &= ~TIM_CCER_CC2E;
tmpccmr1 = TIMx->CCMR1;
tmpccer = TIMx->CCER;
/* Set the filter */
tmpccmr1 &= ~TIM_CCMR1_IC2F;
tmpccmr1 |= (TIM_ICFilter << 12U);
/* Select the Polarity and set the CC2E Bit */
tmpccer &= ~(TIM_CCER_CC2P | TIM_CCER_CC2NP);
tmpccer |= (TIM_ICPolarity << 4U);
/* Write to TIMx CCMR1 and CCER registers */
TIMx->CCMR1 = tmpccmr1 ;
TIMx->CCER = tmpccer;
}
/**
* @brief Configure the TI3 as Input.
* @param TIMx to select the TIM peripheral
* @param TIM_ICPolarity : The Input Polarity.
* This parameter can be one of the following values:
* @arg TIM_ICPolarity_Rising
* @arg TIM_ICPolarity_Falling
* @arg TIM_ICPolarity_BothEdge
* @param TIM_ICSelection: specifies the input to be used.
* This parameter can be one of the following values:
* @arg TIM_ICSelection_DirectTI: TIM Input 3 is selected to be connected to IC3.
* @arg TIM_ICSelection_IndirectTI: TIM Input 3 is selected to be connected to IC4.
* @arg TIM_ICSelection_TRC: TIM Input 3 is selected to be connected to TRC.
* @param TIM_ICFilter: Specifies the Input Capture Filter.
* This parameter must be a value between 0x00 and 0x0F.
* @retval None
*/
static void TIM_TI3_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection,
uint32_t TIM_ICFilter)
{
uint32_t tmpccmr2 = 0U;
uint32_t tmpccer = 0U;
/* Disable the Channel 3: Reset the CC3E Bit */
TIMx->CCER &= ~TIM_CCER_CC3E;
tmpccmr2 = TIMx->CCMR2;
tmpccer = TIMx->CCER;
/* Select the Input */
tmpccmr2 &= ~TIM_CCMR2_CC3S;
tmpccmr2 |= TIM_ICSelection;
/* Set the filter */
tmpccmr2 &= ~TIM_CCMR2_IC3F;
tmpccmr2 |= ((TIM_ICFilter << 4U) & TIM_CCMR2_IC3F);
/* Select the Polarity and set the CC3E Bit */
tmpccer &= ~(TIM_CCER_CC3P | TIM_CCER_CC3NP);
tmpccer |= ((TIM_ICPolarity << 8U) & (TIM_CCER_CC3P | TIM_CCER_CC3NP));
/* Write to TIMx CCMR2 and CCER registers */
TIMx->CCMR2 = tmpccmr2;
TIMx->CCER = tmpccer;
}
/**
* @brief Configure the TI4 as Input.
* @param TIMx to select the TIM peripheral
* @param TIM_ICPolarity : The Input Polarity.
* This parameter can be one of the following values:
* @arg TIM_ICPolarity_Rising
* @arg TIM_ICPolarity_Falling
* @arg TIM_ICPolarity_BothEdge
* @param TIM_ICSelection: specifies the input to be used.
* This parameter can be one of the following values:
* @arg TIM_ICSelection_DirectTI: TIM Input 4 is selected to be connected to IC4.
* @arg TIM_ICSelection_IndirectTI: TIM Input 4 is selected to be connected to IC3.
* @arg TIM_ICSelection_TRC: TIM Input 4 is selected to be connected to TRC.
* @param TIM_ICFilter: Specifies the Input Capture Filter.
* This parameter must be a value between 0x00 and 0x0F.
* @retval None
*/
static void TIM_TI4_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection,
uint32_t TIM_ICFilter)
{
uint32_t tmpccmr2 = 0U;
uint32_t tmpccer = 0U;
/* Disable the Channel 4: Reset the CC4E Bit */
TIMx->CCER &= ~TIM_CCER_CC4E;
tmpccmr2 = TIMx->CCMR2;
tmpccer = TIMx->CCER;
/* Select the Input */
tmpccmr2 &= ~TIM_CCMR2_CC4S;
tmpccmr2 |= (TIM_ICSelection << 8U);
/* Set the filter */
tmpccmr2 &= ~TIM_CCMR2_IC4F;
tmpccmr2 |= ((TIM_ICFilter << 12U) & TIM_CCMR2_IC4F);
/* Select the Polarity and set the CC4E Bit */
tmpccer &= ~(TIM_CCER_CC4P | TIM_CCER_CC4NP);
tmpccer |= ((TIM_ICPolarity << 12U) & (TIM_CCER_CC4P | TIM_CCER_CC4NP));
/* Write to TIMx CCMR2 and CCER registers */
TIMx->CCMR2 = tmpccmr2;
TIMx->CCER = tmpccer ;
}
/**
* @brief Selects the Input Trigger source
* @param TIMx to select the TIM peripheral
* @param InputTriggerSource: The Input Trigger source.
* This parameter can be one of the following values:
* @arg TIM_TS_ITR0: Internal Trigger 0
* @arg TIM_TS_ITR1: Internal Trigger 1
* @arg TIM_TS_ITR2: Internal Trigger 2
* @arg TIM_TS_ITR3: Internal Trigger 3
* @arg TIM_TS_TI1F_ED: TI1 Edge Detector
* @arg TIM_TS_TI1FP1: Filtered Timer Input 1
* @arg TIM_TS_TI2FP2: Filtered Timer Input 2
* @arg TIM_TS_ETRF: External Trigger input
* @retval None
*/
static void TIM_ITRx_SetConfig(TIM_TypeDef *TIMx, uint16_t InputTriggerSource)
{
uint32_t tmpsmcr = 0U;
/* Get the TIMx SMCR register value */
tmpsmcr = TIMx->SMCR;
/* Reset the TS Bits */
tmpsmcr &= ~TIM_SMCR_TS;
/* Set the Input Trigger source and the slave mode*/
tmpsmcr |= InputTriggerSource | TIM_SLAVEMODE_EXTERNAL1;
/* Write to TIMx SMCR */
TIMx->SMCR = tmpsmcr;
}
/**
* @brief Configures the TIMx External Trigger (ETR).
* @param TIMx to select the TIM peripheral
* @param TIM_ExtTRGPrescaler: The external Trigger Prescaler.
* This parameter can be one of the following values:
* @arg TIM_ExtTRGPSC_DIV1: ETRP Prescaler OFF.
* @arg TIM_ExtTRGPSC_DIV2: ETRP frequency divided by 2.
* @arg TIM_ExtTRGPSC_DIV4: ETRP frequency divided by 4.
* @arg TIM_ExtTRGPSC_DIV8: ETRP frequency divided by 8.
* @param TIM_ExtTRGPolarity: The external Trigger Polarity.
* This parameter can be one of the following values:
* @arg TIM_ExtTRGPolarity_Inverted: active low or falling edge active.
* @arg TIM_ExtTRGPolarity_NonInverted: active high or rising edge active.
* @param ExtTRGFilter: External Trigger Filter.
* This parameter must be a value between 0x00 and 0x0F
* @retval None
*/
static void TIM_ETR_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ExtTRGPrescaler,
uint32_t TIM_ExtTRGPolarity, uint32_t ExtTRGFilter)
{
uint32_t tmpsmcr = 0U;
tmpsmcr = TIMx->SMCR;
/* Reset the ETR Bits */
tmpsmcr &= ~(TIM_SMCR_ETF | TIM_SMCR_ETPS | TIM_SMCR_ECE | TIM_SMCR_ETP);
/* Set the Prescaler, the Filter value and the Polarity */
tmpsmcr |= (uint32_t)(TIM_ExtTRGPrescaler | (TIM_ExtTRGPolarity | (ExtTRGFilter << 8)));
/* Write to TIMx SMCR */
TIMx->SMCR = tmpsmcr;
}
/**
* @brief Enables or disables the TIM Capture Compare Channel x.
* @param TIMx to select the TIM peripheral
* @param Channel: specifies the TIM Channel
* This parameter can be one of the following values:
* @arg TIM_Channel_1: TIM Channel 1
* @arg TIM_Channel_2: TIM Channel 2
* @arg TIM_Channel_3: TIM Channel 3
* @arg TIM_Channel_4: TIM Channel 4
* @param ChannelState: specifies the TIM Channel CCxE bit new state.
* This parameter can be: TIM_CCx_ENABLE or TIM_CCx_Disable.
* @retval None
*/
static void TIM_CCxChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelState)
{
uint32_t tmp = 0U;
/* Check the parameters */
assert_param(IS_TIM_CCX_INSTANCE(TIMx,Channel));
tmp = TIM_CCER_CC1E << Channel;
/* Reset the CCxE Bit */
TIMx->CCER &= ~tmp;
/* Set or reset the CCxE Bit */
TIMx->CCER |= (uint32_t)(ChannelState << Channel);
}
/**
* @brief Set the slave timer configuration.
* @param htim : TIM handle
* @param sSlaveConfig: pointer to a TIM_SlaveConfigTypeDef structure that
* contains the selected trigger (internal trigger input, filtered
* timer input or external trigger input) and the ) and the Slave
* mode (Disable, Reset, Gated, Trigger, External clock mode 1).
* @retval None
*/
static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef *htim,
TIM_SlaveConfigTypeDef * sSlaveConfig)
{
uint32_t tmpsmcr = 0U;
uint32_t tmpccmr1 = 0U;
uint32_t tmpccer = 0U;
/* Get the TIMx SMCR register value */
tmpsmcr = htim->Instance->SMCR;
/* Reset the Trigger Selection Bits */
tmpsmcr &= ~TIM_SMCR_TS;
/* Set the Input Trigger source */
tmpsmcr |= sSlaveConfig->InputTrigger;
/* Reset the slave mode Bits */
tmpsmcr &= ~TIM_SMCR_SMS;
/* Set the slave mode */
tmpsmcr |= sSlaveConfig->SlaveMode;
/* Write to TIMx SMCR */
htim->Instance->SMCR = tmpsmcr;
/* Configure the trigger prescaler, filter, and polarity */
switch (sSlaveConfig->InputTrigger)
{
case TIM_TS_ETRF:
{
/* Check the parameters */
assert_param(IS_TIM_ETR_INSTANCE(htim->Instance));
assert_param(IS_TIM_TRIGGERPRESCALER(sSlaveConfig->TriggerPrescaler));
assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity));
assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter));
/* Configure the ETR Trigger source */
TIM_ETR_SetConfig(htim->Instance,
sSlaveConfig->TriggerPrescaler,
sSlaveConfig->TriggerPolarity,
sSlaveConfig->TriggerFilter);
}
break;
case TIM_TS_TI1F_ED:
{
/* Check the parameters */
assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter));
/* Disable the Channel 1: Reset the CC1E Bit */
tmpccer = htim->Instance->CCER;
htim->Instance->CCER &= ~TIM_CCER_CC1E;
tmpccmr1 = htim->Instance->CCMR1;
/* Set the filter */
tmpccmr1 &= ~TIM_CCMR1_IC1F;
tmpccmr1 |= ((sSlaveConfig->TriggerFilter) << 4U);
/* Write to TIMx CCMR1 and CCER registers */
htim->Instance->CCMR1 = tmpccmr1;
htim->Instance->CCER = tmpccer;
}
break;
case TIM_TS_TI1FP1:
{
/* Check the parameters */
assert_param(IS_TIM_CC1_INSTANCE(htim->Instance));
assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity));
assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter));
/* Configure TI1 Filter and Polarity */
TIM_TI1_ConfigInputStage(htim->Instance,
sSlaveConfig->TriggerPolarity,
sSlaveConfig->TriggerFilter);
}
break;
case TIM_TS_TI2FP2:
{
/* Check the parameters */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity));
assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter));
/* Configure TI2 Filter and Polarity */
TIM_TI2_ConfigInputStage(htim->Instance,
sSlaveConfig->TriggerPolarity,
sSlaveConfig->TriggerFilter);
}
break;
case TIM_TS_ITR0:
{
/* Check the parameter */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
}
break;
case TIM_TS_ITR1:
{
/* Check the parameter */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
}
break;
case TIM_TS_ITR2:
{
/* Check the parameter */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
}
break;
case TIM_TS_ITR3:
{
/* Check the parameter */
assert_param(IS_TIM_CC2_INSTANCE(htim->Instance));
}
break;
default:
break;
}
}
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#endif /* HAL_TIM_MODULE_ENABLED */
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/