STM32 firmware for a remotely-controlled stepper motor demo with a mobile interface.
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
f105-motor-demo_stm32/openocd.cfg

158 lines
4.3 KiB

#daemon configuration
telnet_port 4444
gdb_port 3333
#interface
#cat /usr/lib/openocd/interface/olimex-arm-usb-ocd.cfg >> openocd.cfg
#
# STMicroelectronics ST-LINK/V2 in-circuit debugger/programmer
#
interface hla
hla_layout stlink
hla_device_desc "ST-LINK/V2"
hla_vid_pid 0x0483 0x3748
# Optionally specify the serial number of ST-LINK/V2 usb device. ST-LINK/V2
# devices seem to have serial numbers with unreadable characters. ST-LINK/V2
# firmware version >= V2.J21.S4 recommended to avoid issues with adapter serial
# number reset issues.
# eg.
#hla_serial "\xaa\xbc\x6e\x06\x50\x75\xff\x55\x17\x42\x19\x3f"
# target configuration
# cat /usr/lib/openocd/target/stm32.cfg >> openocd.cfg
# script for stm32f3x family
#
# stm32 devices support both JTAG and SWD transports.
#
source [find target/swj-dp.tcl]
source [find mem_helper.tcl]
if { [info exists CHIPNAME] } {
set _CHIPNAME $CHIPNAME
} else {
set _CHIPNAME stm32f3x
}
set _ENDIAN little
# Work-area is a space in RAM used for flash programming
# By default use 16kB
if { [info exists WORKAREASIZE] } {
set _WORKAREASIZE $WORKAREASIZE
} else {
set _WORKAREASIZE 0x4000
}
# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
#
# Since we may be running of an RC oscilator, we crank down the speed a
# bit more to be on the safe side. Perhaps superstition, but if are
# running off a crystal, we can run closer to the limit. Note
# that there can be a pretty wide band where things are more or less stable.
adapter_khz 1000
adapter_nsrst_delay 100
if {[using_jtag]} {
jtag_ntrst_delay 100
}
#jtag scan chain
if { [info exists CPUTAPID] } {
set _CPUTAPID $CPUTAPID
} else {
if { [using_jtag] } {
# See STM Document RM0316
# Section 29.6.3 - corresponds to Cortex-M4 r0p1
set _CPUTAPID 0x4ba00477
} {
set _CPUTAPID 0x2ba01477
}
}
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
if { [info exists BSTAPID] } {
set _BSTAPID $BSTAPID
} else {
# STM Document RM0316 rev 5 for STM32F302/303 B/C size
set _BSTAPID1 0x06422041
# STM Document RM0313 rev 3 for STM32F37x
set _BSTAPID2 0x06432041
# STM Document RM364 rev 1 for STM32F334
set _BSTAPID3 0x06438041
# STM Document RM316 rev 5 for STM32F303 6/8 size
# STM Document RM365 rev 3 for STM32F302 6/8 size
# STM Document RM366 rev 2 for STM32F301 6/8 size
set _BSTAPID4 0x06439041
# STM Document RM016 rev 5 for STM32F303 D/E size
set _BSTAPID5 0x06446041
}
if {[using_jtag]} {
swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
-expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
-expected-id $_BSTAPID4 -expected-id $_BSTAPID5
}
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME stm32f1x 0 0 0 0 $_TARGETNAME
reset_config srst_nogate
if {![using_hla]} {
# if srst is not fitted use SYSRESETREQ to
# perform a soft reset
cortex_m reset_config sysresetreq
}
proc stm32f3x_default_reset_start {} {
# Reset clock is HSI (8 MHz)
adapter_khz 1000
}
proc stm32f3x_default_examine_end {} {
# Enable debug during low power modes (uses more power)
mmw 0xe0042004 0x00000007 0 ;# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
# Stop watchdog counters during halt
mww 0xe0042008 0x00001800 ;# DBGMCU_APB1_FZ = DBG_IWDG_STOP | DBG_WWDG_STOP
}
proc stm32f3x_default_reset_init {} {
# Configure PLL to boost clock to HSI x 8 (64 MHz)
mww 0x40021004 0x00380400 ;# RCC_CFGR = PLLMUL[3:1] | PPRE1[2]
mmw 0x40021000 0x01000000 0 ;# RCC_CR |= PLLON
mww 0x40022000 0x00000012 ;# FLASH_ACR = PRFTBE | LATENCY[1]
sleep 10 ;# Wait for PLL to lock
mmw 0x40021004 0x00000002 0 ;# RCC_CFGR |= SW[1]
# Boost JTAG frequency
adapter_khz 8000
}
# Default hooks
$_TARGETNAME configure -event examine-end { stm32f3x_default_examine_end }
$_TARGETNAME configure -event reset-start { stm32f3x_default_reset_start }
$_TARGETNAME configure -event reset-init { stm32f3x_default_reset_init }
$_TARGETNAME configure -event trace-config {
# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
# change this value accordingly to configure trace pins
# assignment
mmw 0xe0042004 0x00000020 0
}