Demo application running on STM8 demonstrating a web interface with ESPTerm
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
espterm-stm8-demo/Libraries/SPL/inc/stm8s_uart2.h

447 lines
18 KiB

/**
********************************************************************************
* @file stm8s_uart2.h
* @author MCD Application Team
* @version V2.2.0
* @date 30-September-2014
* @brief This file contains all functions prototypes and macros for the UART2 peripheral.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT 2014 STMicroelectronics</center></h2>
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM8S_UART2_H
#define __STM8S_UART2_H
/* Includes ------------------------------------------------------------------*/
#include "stm8s.h"
/** @addtogroup STM8S_StdPeriph_Driver
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @addtogroup UART2_Exported_Types
* @{
*/
/**
* @brief UART2 Irda Modes
*/
typedef enum { UART2_IRDAMODE_NORMAL = (uint8_t)0x00, /**< 0x00 Irda Normal Mode */
UART2_IRDAMODE_LOWPOWER = (uint8_t)0x01 /**< 0x01 Irda Low Power Mode */
} UART2_IrDAMode_TypeDef;
/**
* @brief UART2 WakeUP Modes
*/
typedef enum { UART2_WAKEUP_IDLELINE = (uint8_t)0x00, /**< 0x01 Idle Line wake up */
UART2_WAKEUP_ADDRESSMARK = (uint8_t)0x08 /**< 0x02 Address Mark wake up */
} UART2_WakeUp_TypeDef;
/**
* @brief UART2 LIN Break detection length possible values
*/
typedef enum { UART2_LINBREAKDETECTIONLENGTH_10BITS = (uint8_t)0x00, /**< 0x01 10 bits Lin Break detection */
UART2_LINBREAKDETECTIONLENGTH_11BITS = (uint8_t)0x01 /**< 0x02 11 bits Lin Break detection */
} UART2_LINBreakDetectionLength_TypeDef;
/**
* @brief UART2 stop bits possible values
*/
typedef enum { UART2_STOPBITS_1 = (uint8_t)0x00, /**< One stop bit is transmitted at the end of frame*/
UART2_STOPBITS_0_5 = (uint8_t)0x10, /**< Half stop bits is transmitted at the end of frame*/
UART2_STOPBITS_2 = (uint8_t)0x20, /**< Two stop bits are transmitted at the end of frame*/
UART2_STOPBITS_1_5 = (uint8_t)0x30 /**< One and half stop bits*/
} UART2_StopBits_TypeDef;
/**
* @brief UART2 parity possible values
*/
typedef enum { UART2_PARITY_NO = (uint8_t)0x00, /**< No Parity*/
UART2_PARITY_EVEN = (uint8_t)0x04, /**< Even Parity*/
UART2_PARITY_ODD = (uint8_t)0x06 /**< Odd Parity*/
} UART2_Parity_TypeDef;
/**
* @brief UART2 Mode possible values
*/
typedef enum { UART2_LIN_MODE_MASTER = (uint8_t)0x00, /**< LIN Master Mode*/
UART2_LIN_MODE_SLAVE = (uint8_t)0x01 /**< LIN Slave Mode*/
} UART2_LinMode_TypeDef;
/**
* @brief UART2 automatic resynchronisation possible values
*/
typedef enum { UART2_LIN_AUTOSYNC_DISABLE = (uint8_t)0x00, /**< LIN Autosynchronization Disable*/
UART2_LIN_AUTOSYNC_ENABLE = (uint8_t)0x01 /**< LIN Autosynchronization Enable*/
} UART2_LinAutosync_TypeDef;
/**
* @brief UART2 Divider Update Method possible values
*/
typedef enum { UART2_LIN_DIVUP_LBRR1 = (uint8_t)0x00, /**< LIN LDIV is updated as soon as LBRR1 is written*/
UART2_LIN_DIVUP_NEXTRXNE = (uint8_t)0x01 /**< LIN LDIV is updated at the next received character*/
} UART2_LinDivUp_TypeDef;
/**
* @brief UART2 Synchrone modes
*/
typedef enum { UART2_SYNCMODE_CLOCK_DISABLE = (uint8_t)0x80, /**< 0x80 Sync mode Disable, SLK pin Disable */
UART2_SYNCMODE_CLOCK_ENABLE = (uint8_t)0x08, /**< 0x08 Sync mode Enable, SLK pin Enable */
UART2_SYNCMODE_CPOL_LOW = (uint8_t)0x40, /**< 0x40 Steady low value on SCLK pin outside transmission window */
UART2_SYNCMODE_CPOL_HIGH = (uint8_t)0x04, /**< 0x04 Steady high value on SCLK pin outside transmission window */
UART2_SYNCMODE_CPHA_MIDDLE = (uint8_t)0x20, /**< 0x20 SCLK clock line activated in middle of data bit */
UART2_SYNCMODE_CPHA_BEGINING = (uint8_t)0x02, /**< 0x02 SCLK clock line activated at beginning of data bit */
UART2_SYNCMODE_LASTBIT_DISABLE = (uint8_t)0x10, /**< 0x10 The clock pulse of the last data bit is not output to the SCLK pin */
UART2_SYNCMODE_LASTBIT_ENABLE = (uint8_t)0x01 /**< 0x01 The clock pulse of the last data bit is output to the SCLK pin */
} UART2_SyncMode_TypeDef;
/**
* @brief UART2 Word length possible values
*/
typedef enum { UART2_WORDLENGTH_8D = (uint8_t)0x00,/**< 0x00 8 bits Data */
UART2_WORDLENGTH_9D = (uint8_t)0x10 /**< 0x10 9 bits Data */
} UART2_WordLength_TypeDef;
/**
* @brief UART2 Mode possible values
*/
typedef enum { UART2_MODE_RX_ENABLE = (uint8_t)0x08, /**< 0x08 Receive Enable */
UART2_MODE_TX_ENABLE = (uint8_t)0x04, /**< 0x04 Transmit Enable */
UART2_MODE_TX_DISABLE = (uint8_t)0x80, /**< 0x80 Transmit Disable */
UART2_MODE_RX_DISABLE = (uint8_t)0x40, /**< 0x40 Single-wire Half-duplex mode */
UART2_MODE_TXRX_ENABLE = (uint8_t)0x0C /**< 0x0C Transmit Enable and Receive Enable */
} UART2_Mode_TypeDef;
/**
* @brief UART2 Flag possible values
*/
typedef enum
{
UART2_FLAG_TXE = (uint16_t)0x0080, /*!< Transmit Data Register Empty flag */
UART2_FLAG_TC = (uint16_t)0x0040, /*!< Transmission Complete flag */
UART2_FLAG_RXNE = (uint16_t)0x0020, /*!< Read Data Register Not Empty flag */
UART2_FLAG_IDLE = (uint16_t)0x0010, /*!< Idle line detected flag */
UART2_FLAG_OR_LHE = (uint16_t)0x0008, /*!< OverRun error flag */
UART2_FLAG_NF = (uint16_t)0x0004, /*!< Noise error flag */
UART2_FLAG_FE = (uint16_t)0x0002, /*!< Framing Error flag */
UART2_FLAG_PE = (uint16_t)0x0001, /*!< Parity Error flag */
UART2_FLAG_SBK = (uint16_t)0x0101, /**< Send Break Complete interrupt flag */
UART2_FLAG_LBDF = (uint16_t)0x0210, /**< LIN Break Detection Flag */
UART2_FLAG_LHDF = (uint16_t)0x0302, /**< LIN Header Detection Flag*/
UART2_FLAG_LSF = (uint16_t)0x0301 /**< LIN Sync Field Flag*/
} UART2_Flag_TypeDef;
/**
* @brief UART2 Interrupt definition
* UART2_IT possible values
* Elements values convention: 0xZYX
* X: Position of the corresponding Interrupt
* - For the following values, X means the interrupt position in the CR2 register.
* UART2_IT_TXE
* UART2_IT_TC
* UART2_IT_RXNE
* UART2_IT_IDLE
* UART2_IT_OR
* - For the UART2_IT_PE value, X means the flag position in the CR1 register.
* - For the UART2_IT_LBDF value, X means the flag position in the CR4 register.
* - For the UART2_IT_LHDF value, X means the flag position in the CR6 register.
* Y: Flag position
* - For the following values, Y means the flag (pending bit) position in the SR register.
* UART2_IT_TXE
* UART2_IT_TC
* UART2_IT_RXNE
* UART2_IT_IDLE
* UART2_IT_OR
* UART2_IT_PE
* - For the UART2_IT_LBDF value, Y means the flag position in the CR4 register.
* - For the UART2_IT_LHDF value, Y means the flag position in the CR6 register.
* Z: Register index: indicate in which register the dedicated interrupt source is:
* - 1==> CR1 register
* - 2==> CR2 register
* - 3==> CR4 register
* - 4==> CR6 register
*/
typedef enum { UART2_IT_TXE = (uint16_t)0x0277, /**< Transmit interrupt */
UART2_IT_TC = (uint16_t)0x0266, /**< Transmission Complete interrupt */
UART2_IT_RXNE = (uint16_t)0x0255, /**< Data Register Not Empty interrupt */
UART2_IT_IDLE = (uint16_t)0x0244, /**< Idle line detected interrupt */
UART2_IT_OR = (uint16_t)0x0235, /**< OverRun error interrupt */
UART2_IT_PE = (uint16_t)0x0100, /**< Parity Error interrupt */
UART2_IT_LBDF = (uint16_t)0x0346, /**< LIN Break Detection interrupt */
UART2_IT_LHDF = (uint16_t)0x0412, /**< LIN Header Detection interrupt*/
UART2_IT_RXNE_OR = (uint16_t)0x0205 /*!< Receive/Overrun interrupt */
} UART2_IT_TypeDef;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/* Exported macros ------------------------------------------------------------*/
/* Private macros ------------------------------------------------------------*/
/** @addtogroup UART2_Private_Macros
* @{
*/
/**
* @brief Macro used by the assert function to check the different functions parameters.
*/
/**
* @brief Macro used by the assert_param function in order to check the different
* sensitivity values for the MODEs possible combination should be one of
* the following.
*/
#define IS_UART2_MODE_OK(Mode) \
(((Mode) == (uint8_t)UART2_MODE_RX_ENABLE) || \
((Mode) == (uint8_t)UART2_MODE_RX_DISABLE) || \
((Mode) == (uint8_t)UART2_MODE_TX_ENABLE) || \
((Mode) == (uint8_t)UART2_MODE_TX_DISABLE) || \
((Mode) == (uint8_t)UART2_MODE_TXRX_ENABLE) || \
((Mode) == (uint8_t)((uint8_t)UART2_MODE_TX_ENABLE|(uint8_t)UART2_MODE_RX_ENABLE)) || \
((Mode) == (uint8_t)((uint8_t)UART2_MODE_TX_ENABLE|(uint8_t)UART2_MODE_RX_DISABLE)) || \
((Mode) == (uint8_t)((uint8_t)UART2_MODE_TX_DISABLE|(uint8_t)UART2_MODE_RX_DISABLE)) || \
((Mode) == (uint8_t)((uint8_t)UART2_MODE_TX_DISABLE|(uint8_t)UART2_MODE_RX_ENABLE)))
/**
* @brief Macro used by the assert_param function in order to check the different
* sensitivity values for the WordLengths
*/
#define IS_UART2_WORDLENGTH_OK(WordLength) \
(((WordLength) == UART2_WORDLENGTH_8D) || \
((WordLength) == UART2_WORDLENGTH_9D))
/**
* @brief Macro used by the assert_param function in order to check the different
* sensitivity values for the SyncModes; it should exclude values such
* as UART2_CLOCK_ENABLE|UART2_CLOCK_DISABLE
*/
#define IS_UART2_SYNCMODE_OK(SyncMode) \
(!((((SyncMode)&(((uint8_t)UART2_SYNCMODE_CLOCK_ENABLE)|((uint8_t)UART2_SYNCMODE_CLOCK_DISABLE))) == (((uint8_t)UART2_SYNCMODE_CLOCK_ENABLE)|((uint8_t)UART2_SYNCMODE_CLOCK_DISABLE))) || \
(((SyncMode)&(((uint8_t)UART2_SYNCMODE_CPOL_LOW )|((uint8_t)UART2_SYNCMODE_CPOL_HIGH))) == (((uint8_t)UART2_SYNCMODE_CPOL_LOW )|((uint8_t)UART2_SYNCMODE_CPOL_HIGH))) || \
(((SyncMode)&(((uint8_t)UART2_SYNCMODE_CPHA_MIDDLE)|((uint8_t)UART2_SYNCMODE_CPHA_BEGINING))) == (((uint8_t)UART2_SYNCMODE_CPHA_MIDDLE)|((uint8_t)UART2_SYNCMODE_CPHA_BEGINING))) || \
(((SyncMode)&(((uint8_t)UART2_SYNCMODE_LASTBIT_DISABLE)|((uint8_t)UART2_SYNCMODE_LASTBIT_ENABLE))) == (((uint8_t)UART2_SYNCMODE_LASTBIT_DISABLE)|((uint8_t)UART2_SYNCMODE_LASTBIT_ENABLE)))))
/**
* @brief Macro used by the assert_param function in order to check the
* different sensitivity values for the FLAGs
*/
#define IS_UART2_FLAG_OK(Flag) \
(((Flag) == UART2_FLAG_TXE) || \
((Flag) == UART2_FLAG_TC) || \
((Flag) == UART2_FLAG_RXNE) || \
((Flag) == UART2_FLAG_IDLE) || \
((Flag) == UART2_FLAG_OR_LHE) || \
((Flag) == UART2_FLAG_NF) || \
((Flag) == UART2_FLAG_FE) || \
((Flag) == UART2_FLAG_PE) || \
((Flag) == UART2_FLAG_SBK) || \
((Flag) == UART2_FLAG_LSF) || \
((Flag) == UART2_FLAG_LHDF) || \
((Flag) == UART2_FLAG_LBDF))
/**
* @brief Macro used by the assert_param function in order to check the
* different sensitivity values for the FLAGs that can be cleared by writing 0
*/
#define IS_UART2_CLEAR_FLAG_OK(Flag) \
(((Flag) == UART2_FLAG_RXNE) || \
((Flag) == UART2_FLAG_LHDF) || \
((Flag) == UART2_FLAG_LSF) || \
((Flag) == UART2_FLAG_LBDF))
/**
* @brief Macro used by the assert_param function in order to check
* the different sensitivity values for the Interrupts
*/
#define IS_UART2_CONFIG_IT_OK(Interrupt) \
(((Interrupt) == UART2_IT_PE) || \
((Interrupt) == UART2_IT_TXE) || \
((Interrupt) == UART2_IT_TC) || \
((Interrupt) == UART2_IT_RXNE_OR ) || \
((Interrupt) == UART2_IT_IDLE) || \
((Interrupt) == UART2_IT_LHDF) || \
((Interrupt) == UART2_IT_LBDF))
/**
* @brief Macro used by the assert function in order to check the different
* sensitivity values for the pending bit
*/
#define IS_UART2_GET_IT_OK(ITPendingBit) \
(((ITPendingBit) == UART2_IT_TXE) || \
((ITPendingBit) == UART2_IT_TC) || \
((ITPendingBit) == UART2_IT_RXNE) || \
((ITPendingBit) == UART2_IT_IDLE) || \
((ITPendingBit) == UART2_IT_OR) || \
((ITPendingBit) == UART2_IT_LBDF) || \
((ITPendingBit) == UART2_IT_LHDF) || \
((ITPendingBit) == UART2_IT_PE))
/**
* @brief Macro used by the assert function in order to check the different
* sensitivity values for the pending bit that can be cleared by writing 0
*/
#define IS_UART2_CLEAR_IT_OK(ITPendingBit) \
(((ITPendingBit) == UART2_IT_RXNE) || \
((ITPendingBit) == UART2_IT_LHDF) || \
((ITPendingBit) == UART2_IT_LBDF))
/**
* @brief Macro used by the assert_param function in order to check the different
* sensitivity values for the IrDAModes
*/
#define IS_UART2_IRDAMODE_OK(IrDAMode) \
(((IrDAMode) == UART2_IRDAMODE_LOWPOWER) || \
((IrDAMode) == UART2_IRDAMODE_NORMAL))
/**
* @brief Macro used by the assert_param function in order to check the different
* sensitivity values for the WakeUps
*/
#define IS_UART2_WAKEUP_OK(WakeUp) \
(((WakeUp) == UART2_WAKEUP_IDLELINE) || \
((WakeUp) == UART2_WAKEUP_ADDRESSMARK))
/**
* @brief Macro used by the assert_param function in order to check the different
* sensitivity values for the LINBreakDetectionLengths
*/
#define IS_UART2_LINBREAKDETECTIONLENGTH_OK(LINBreakDetectionLength) \
(((LINBreakDetectionLength) == UART2_LINBREAKDETECTIONLENGTH_10BITS) || \
((LINBreakDetectionLength) == UART2_LINBREAKDETECTIONLENGTH_11BITS))
/**
* @brief Macro used by the assert_param function in order to check the different
* sensitivity values for the UART2_StopBits
*/
#define IS_UART2_STOPBITS_OK(StopBit) (((StopBit) == UART2_STOPBITS_1) || \
((StopBit) == UART2_STOPBITS_0_5) || \
((StopBit) == UART2_STOPBITS_2) || \
((StopBit) == UART2_STOPBITS_1_5 ))
/**
* @brief Macro used by the assert_param function in order to check the different
* sensitivity values for the Paritys
*/
#define IS_UART2_PARITY_OK(Parity) (((Parity) == UART2_PARITY_NO) || \
((Parity) == UART2_PARITY_EVEN) || \
((Parity) == UART2_PARITY_ODD ))
/**
* @brief Macro used by the assert_param function in order to check the maximum
* baudrate value
*/
#define IS_UART2_BAUDRATE_OK(NUM) ((NUM) <= (uint32_t)625000)
/**
* @brief Macro used by the assert_param function in order to check the address
* of the UART2 or UART node
*/
#define UART2_ADDRESS_MAX ((uint8_t)16)
#define IS_UART2_ADDRESS_OK(node) ((node) < UART2_ADDRESS_MAX )
/**
* @brief Macro used by the assert_param function in order to check the LIN mode
*/
#define IS_UART2_SLAVE_OK(Mode) \
(((Mode) == UART2_LIN_MODE_MASTER) || \
((Mode) == UART2_LIN_MODE_SLAVE))
/**
* @brief Macro used by the assert_param function in order to check the LIN
* automatic resynchronization mode
*/
#define IS_UART2_AUTOSYNC_OK(AutosyncMode) \
(((AutosyncMode) == UART2_LIN_AUTOSYNC_ENABLE) || \
((AutosyncMode) == UART2_LIN_AUTOSYNC_DISABLE))
/**
* @brief Macro used by the assert_param function in order to check the LIN divider update method
*/
#define IS_UART2_DIVUP_OK(DivupMethod) \
(((DivupMethod) == UART2_LIN_DIVUP_LBRR1) || \
((DivupMethod) == UART2_LIN_DIVUP_NEXTRXNE))
/**
* @}
*/
/* Exported functions ------------------------------------------------------- */
/** @addtogroup UART2_Exported_Functions
* @{
*/
void UART2_DeInit(void);
void UART2_Init(uint32_t BaudRate, UART2_WordLength_TypeDef WordLength,
UART2_StopBits_TypeDef StopBits, UART2_Parity_TypeDef Parity,
UART2_SyncMode_TypeDef SyncMode, UART2_Mode_TypeDef Mode);
void UART2_Cmd(FunctionalState NewState);
void UART2_ITConfig(UART2_IT_TypeDef UART2_IT, FunctionalState NewState);
void UART2_HalfDuplexCmd(FunctionalState NewState);
void UART2_IrDAConfig(UART2_IrDAMode_TypeDef UART2_IrDAMode);
void UART2_IrDACmd(FunctionalState NewState);
void UART2_LINBreakDetectionConfig(UART2_LINBreakDetectionLength_TypeDef UART2_LINBreakDetectionLength);
void UART2_LINConfig(UART2_LinMode_TypeDef UART2_Mode,
UART2_LinAutosync_TypeDef UART2_Autosync,
UART2_LinDivUp_TypeDef UART2_DivUp);
void UART2_LINCmd(FunctionalState NewState);
void UART2_SmartCardCmd(FunctionalState NewState);
void UART2_SmartCardNACKCmd(FunctionalState NewState);
void UART2_WakeUpConfig(UART2_WakeUp_TypeDef UART2_WakeUp);
void UART2_ReceiverWakeUpCmd(FunctionalState NewState);
uint8_t UART2_ReceiveData8(void);
uint16_t UART2_ReceiveData9(void);
void UART2_SendData8(uint8_t Data);
void UART2_SendData9(uint16_t Data);
void UART2_SendBreak(void);
void UART2_SetAddress(uint8_t UART2_Address);
void UART2_SetGuardTime(uint8_t UART2_GuardTime);
void UART2_SetPrescaler(uint8_t UART2_Prescaler);
FlagStatus UART2_GetFlagStatus(UART2_Flag_TypeDef UART2_FLAG);
void UART2_ClearFlag(UART2_Flag_TypeDef UART2_FLAG);
ITStatus UART2_GetITStatus(UART2_IT_TypeDef UART2_IT);
void UART2_ClearITPendingBit(UART2_IT_TypeDef UART2_IT);
/**
* @}
*/
#endif /* __STM8S_UART2_H */
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/