Demo application running on STM8 demonstrating a web interface with ESPTerm
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
espterm-stm8-demo/Libraries/SPL/inc/stm8s_flash.h

300 lines
13 KiB

/**
******************************************************************************
* @file stm8s_flash.h
* @author MCD Application Team
* @version V2.2.0
* @date 30-September-2014
* @brief This file contains all functions prototype and macros for the FLASH peripheral.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT 2014 STMicroelectronics</center></h2>
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM8S_FLASH_H
#define __STM8S_FLASH_H
/* Includes ------------------------------------------------------------------*/
#include "stm8s.h"
/* Exported constants --------------------------------------------------------*/
/** @addtogroup FLASH_Exported_Constants
* @{
*/
#define FLASH_PROG_START_PHYSICAL_ADDRESS ((uint32_t)0x008000) /*!< Program memory: start address */
#if defined (STM8S208) || defined(STM8S207) || defined(STM8S007) || defined (STM8AF52Ax) || defined (STM8AF62Ax)
#define FLASH_PROG_END_PHYSICAL_ADDRESS ((uint32_t)0x027FFF) /*!< Program memory: end address */
#define FLASH_PROG_BLOCKS_NUMBER ((uint16_t)1024) /*!< Program memory: total number of blocks */
#define FLASH_DATA_START_PHYSICAL_ADDRESS ((uint32_t)0x004000) /*!< Data EEPROM memory: start address */
#define FLASH_DATA_END_PHYSICAL_ADDRESS ((uint32_t)0x0047FF) /*!< Data EEPROM memory: end address */
#define FLASH_DATA_BLOCKS_NUMBER ((uint16_t)16) /*!< Data EEPROM memory: total number of blocks */
#define FLASH_BLOCK_SIZE ((uint8_t)128) /*!< Number of bytes in a block (common for Program and Data memories) */
#endif /* STM8S208, STM8S207, STM8S007, STM8AF52Ax, STM8AF62Ax */
#if defined(STM8S105) || defined(STM8S005) || defined(STM8AF626x)
#define FLASH_PROG_END_PHYSICAL_ADDRESS ((uint32_t)0xFFFF) /*!< Program memory: end address */
#define FLASH_PROG_BLOCKS_NUMBER ((uint16_t)256) /*!< Program memory: total number of blocks */
#define FLASH_DATA_START_PHYSICAL_ADDRESS ((uint32_t)0x004000) /*!< Data EEPROM memory: start address */
#define FLASH_DATA_END_PHYSICAL_ADDRESS ((uint32_t)0x0043FF) /*!< Data EEPROM memory: end address */
#define FLASH_DATA_BLOCKS_NUMBER ((uint16_t)8) /*!< Data EEPROM memory: total number of blocks */
#define FLASH_BLOCK_SIZE ((uint8_t)128) /*!< Number of bytes in a block (common for Program and Data memories) */
#endif /* STM8S105 or STM8AF626x */
#if defined(STM8S103) || defined(STM8S003) || defined(STM8S903) || defined(STM8AF622x)
#define FLASH_PROG_END_PHYSICAL_ADDRESS ((uint32_t)0x9FFF) /*!< Program memory: end address */
#define FLASH_PROG_BLOCKS_NUMBER ((uint16_t)128) /*!< Program memory: total number of blocks */
#define FLASH_DATA_START_PHYSICAL_ADDRESS ((uint32_t)0x004000) /*!< Data EEPROM memory: start address */
#define FLASH_DATA_END_PHYSICAL_ADDRESS ((uint32_t)0x00427F) /*!< Data EEPROM memory: end address */
#define FLASH_DATA_BLOCKS_NUMBER ((uint16_t)10) /*!< Data EEPROM memory: total number of blocks */
#define FLASH_BLOCK_SIZE ((uint8_t)64) /*!< Number of bytes in a block (common for Program and Data memories) */
#endif /* STM8S103 or STM8S003 or STM8S903 or STM8AF622x*/
#define FLASH_RASS_KEY1 ((uint8_t)0x56) /*!< First RASS key */
#define FLASH_RASS_KEY2 ((uint8_t)0xAE) /*!< Second RASS key */
#define OPTION_BYTE_START_PHYSICAL_ADDRESS ((uint16_t)0x4800)
#define OPTION_BYTE_END_PHYSICAL_ADDRESS ((uint16_t)0x487F)
#define FLASH_OPTIONBYTE_ERROR ((uint16_t)0x5555) /*!< Error code option byte
(if value read is not equal to complement value read) */
/**
* @}
*/
/* Exported types ------------------------------------------------------------*/
/** @addtogroup FLASH_Exported_Types
* @{
*/
/**
* @brief FLASH Memory types
*/
typedef enum {
FLASH_MEMTYPE_PROG = (uint8_t)0xFD, /*!< Program memory */
FLASH_MEMTYPE_DATA = (uint8_t)0xF7 /*!< Data EEPROM memory */
} FLASH_MemType_TypeDef;
/**
* @brief FLASH programming modes
*/
typedef enum {
FLASH_PROGRAMMODE_STANDARD = (uint8_t)0x00, /*!< Standard programming mode */
FLASH_PROGRAMMODE_FAST = (uint8_t)0x10 /*!< Fast programming mode */
} FLASH_ProgramMode_TypeDef;
/**
* @brief FLASH fixed programming time
*/
typedef enum {
FLASH_PROGRAMTIME_STANDARD = (uint8_t)0x00, /*!< Standard programming time fixed at 1/2 tprog */
FLASH_PROGRAMTIME_TPROG = (uint8_t)0x01 /*!< Programming time fixed at tprog */
} FLASH_ProgramTime_TypeDef;
/**
* @brief FLASH Low Power mode select
*/
typedef enum {
FLASH_LPMODE_POWERDOWN = (uint8_t)0x04, /*!< HALT: Power-Down / ACTIVE-HALT: Power-Down */
FLASH_LPMODE_STANDBY = (uint8_t)0x08, /*!< HALT: Standby / ACTIVE-HALT: Standby */
FLASH_LPMODE_POWERDOWN_STANDBY = (uint8_t)0x00, /*!< HALT: Power-Down / ACTIVE-HALT: Standby */
FLASH_LPMODE_STANDBY_POWERDOWN = (uint8_t)0x0C /*!< HALT: Standby / ACTIVE-HALT: Power-Down */
}
FLASH_LPMode_TypeDef;
/**
* @brief FLASH status of the last operation
*/
typedef enum {
#if defined (STM8S208) || defined(STM8S207) || defined(STM8S007) || defined(STM8S105) || \
defined(STM8S005) || defined (STM8AF52Ax) || defined (STM8AF62Ax) || defined(STM8AF626x)
FLASH_STATUS_END_HIGH_VOLTAGE = (uint8_t)0x40, /*!< End of high voltage */
#endif /* STM8S208, STM8S207, STM8S105, STM8AF62Ax, STM8AF52Ax, STM8AF626x */
FLASH_STATUS_SUCCESSFUL_OPERATION = (uint8_t)0x04, /*!< End of operation flag */
FLASH_STATUS_TIMEOUT = (uint8_t)0x02, /*!< Time out error */
FLASH_STATUS_WRITE_PROTECTION_ERROR = (uint8_t)0x01 /*!< Write attempted to protected page */
} FLASH_Status_TypeDef;
/**
* @brief FLASH flags definition
* - Warning : FLAG value = mapping position register
*/
typedef enum {
#if defined (STM8S208) || defined(STM8S207) || defined(STM8S007) || defined(STM8S105) || \
defined(STM8S005) || defined (STM8AF52Ax) || defined (STM8AF62Ax) || defined(STM8AF626x)
FLASH_FLAG_HVOFF = (uint8_t)0x40, /*!< End of high voltage flag */
#endif /* STM8S208, STM8S207, STM8S105, STM8AF62Ax, STM8AF52Ax, STM8AF626x */
FLASH_FLAG_DUL = (uint8_t)0x08, /*!< Data EEPROM unlocked flag */
FLASH_FLAG_EOP = (uint8_t)0x04, /*!< End of programming (write or erase operation) flag */
FLASH_FLAG_PUL = (uint8_t)0x02, /*!< Flash Program memory unlocked flag */
FLASH_FLAG_WR_PG_DIS = (uint8_t)0x01 /*!< Write attempted to protected page flag */
} FLASH_Flag_TypeDef;
/**
* @}
*/
/* Private macros ------------------------------------------------------------*/
/**
* @brief Macros used by the assert function in order to check the different functions parameters.
* @addtogroup FLASH_Private_Macros
* @{
*/
/**
* @brief Macro used by the assert function in order to check the different sensitivity values for the flash program Address
*/
#define IS_FLASH_PROG_ADDRESS_OK(ADDRESS) (((ADDRESS) >= FLASH_PROG_START_PHYSICAL_ADDRESS) && \
((ADDRESS) <= FLASH_PROG_END_PHYSICAL_ADDRESS))
/**
* @brief Macro used by the assert function in order to check the different sensitivity values for the data eeprom Address
*/
#define IS_FLASH_DATA_ADDRESS_OK(ADDRESS) (((ADDRESS) >= FLASH_DATA_START_PHYSICAL_ADDRESS) && \
((ADDRESS) <= FLASH_DATA_END_PHYSICAL_ADDRESS))
/**
* @brief Macro used by the assert function in order to check the different sensitivity values for the data eeprom and flash program Address
*/
#define IS_FLASH_ADDRESS_OK(ADDRESS)((((ADDRESS) >= FLASH_PROG_START_PHYSICAL_ADDRESS) && ((ADDRESS) <= FLASH_PROG_END_PHYSICAL_ADDRESS)) || \
(((ADDRESS) >= FLASH_DATA_START_PHYSICAL_ADDRESS) && ((ADDRESS) <= FLASH_DATA_END_PHYSICAL_ADDRESS)))
/**
* @brief Macro used by the assert function in order to check the different sensitivity values for the flash program Block number
*/
#define IS_FLASH_PROG_BLOCK_NUMBER_OK(BLOCKNUM) ((BLOCKNUM) < FLASH_PROG_BLOCKS_NUMBER)
/**
* @brief Macro used by the assert function in order to check the different sensitivity values for the data eeprom Block number
*/
#define IS_FLASH_DATA_BLOCK_NUMBER_OK(BLOCKNUM) ((BLOCKNUM) < FLASH_DATA_BLOCKS_NUMBER)
/**
* @brief Macro used by the assert function in order to check the different sensitivity values for the flash memory type
*/
#define IS_MEMORY_TYPE_OK(MEMTYPE) (((MEMTYPE) == FLASH_MEMTYPE_PROG) || \
((MEMTYPE) == FLASH_MEMTYPE_DATA))
/**
* @brief Macro used by the assert function in order to check the different sensitivity values for the flash program mode
*/
#define IS_FLASH_PROGRAM_MODE_OK(MODE) (((MODE) == FLASH_PROGRAMMODE_STANDARD) || \
((MODE) == FLASH_PROGRAMMODE_FAST))
/**
* @brief Macro used by the assert function in order to check the program time mode
*/
#define IS_FLASH_PROGRAM_TIME_OK(TIME) (((TIME) == FLASH_PROGRAMTIME_STANDARD) || \
((TIME) == FLASH_PROGRAMTIME_TPROG))
/**
* @brief Macro used by the assert function in order to check the different
* sensitivity values for the low power mode
*/
#define IS_FLASH_LOW_POWER_MODE_OK(LPMODE) (((LPMODE) == FLASH_LPMODE_POWERDOWN) || \
((LPMODE) == FLASH_LPMODE_STANDBY) || \
((LPMODE) == FLASH_LPMODE_POWERDOWN_STANDBY) || \
((LPMODE) == FLASH_LPMODE_STANDBY_POWERDOWN))
/**
* @brief Macro used by the assert function in order to check the different
* sensitivity values for the option bytes Address
*/
#define IS_OPTION_BYTE_ADDRESS_OK(ADDRESS) (((ADDRESS) >= OPTION_BYTE_START_PHYSICAL_ADDRESS) && \
((ADDRESS) <= OPTION_BYTE_END_PHYSICAL_ADDRESS))
/**
* @brief Macro used by the assert function in order to check the different flags values
*/
#if defined (STM8S208) || defined(STM8S207) || defined(STM8S007) || defined(STM8S105) || \
defined(STM8S005) || defined (STM8AF52Ax) || defined (STM8AF62Ax) || defined(STM8AF626x)
#define IS_FLASH_FLAGS_OK(FLAG) (((FLAG) == FLASH_FLAG_HVOFF) || \
((FLAG) == FLASH_FLAG_DUL) || \
((FLAG) == FLASH_FLAG_EOP) || \
((FLAG) == FLASH_FLAG_PUL) || \
((FLAG) == FLASH_FLAG_WR_PG_DIS))
#else /* STM8S103, STM8S903, STM8AF622x */
#define IS_FLASH_FLAGS_OK(FLAG) (((FLAG) == FLASH_FLAG_DUL) || \
((FLAG) == FLASH_FLAG_EOP) || \
((FLAG) == FLASH_FLAG_PUL) || \
((FLAG) == FLASH_FLAG_WR_PG_DIS))
#endif /* STM8S208, STM8S207, STM8S105, STM8AF62Ax, STM8AF52Ax, STM8AF626x */
/**
* @}
*/
/* Exported functions ------------------------------------------------------- */
/** @addtogroup FLASH_Exported_Functions
* @{
*/
void FLASH_Unlock(FLASH_MemType_TypeDef FLASH_MemType);
void FLASH_Lock(FLASH_MemType_TypeDef FLASH_MemType);
void FLASH_DeInit(void);
void FLASH_ITConfig(FunctionalState NewState);
void FLASH_EraseByte(uint32_t Address);
void FLASH_ProgramByte(uint32_t Address, uint8_t Data);
uint8_t FLASH_ReadByte(uint32_t Address);
void FLASH_ProgramWord(uint32_t Address, uint32_t Data);
uint16_t FLASH_ReadOptionByte(uint16_t Address);
void FLASH_ProgramOptionByte(uint16_t Address, uint8_t Data);
void FLASH_EraseOptionByte(uint16_t Address);
void FLASH_SetLowPowerMode(FLASH_LPMode_TypeDef FLASH_LPMode);
void FLASH_SetProgrammingTime(FLASH_ProgramTime_TypeDef FLASH_ProgTime);
FLASH_LPMode_TypeDef FLASH_GetLowPowerMode(void);
FLASH_ProgramTime_TypeDef FLASH_GetProgrammingTime(void);
uint32_t FLASH_GetBootSize(void);
FlagStatus FLASH_GetFlagStatus(FLASH_Flag_TypeDef FLASH_FLAG);
/**
@code
All the functions declared below must be executed from RAM exclusively, except
for the FLASH_WaitForLastOperation function which can be executed from Flash.
Steps of the execution from RAM differs from one toolchain to another.
for more details refer to stm8s_flash.c file.
To enable execution from RAM you can either uncomment the following define
in the stm8s.h file or define it in your toolchain compiler preprocessor
- #define RAM_EXECUTION (1)
@endcode
*/
IN_RAM(void FLASH_EraseBlock(uint16_t BlockNum, FLASH_MemType_TypeDef FLASH_MemType));
IN_RAM(void FLASH_ProgramBlock(uint16_t BlockNum, FLASH_MemType_TypeDef FLASH_MemType,
FLASH_ProgramMode_TypeDef FLASH_ProgMode, uint8_t *Buffer));
IN_RAM(FLASH_Status_TypeDef FLASH_WaitForLastOperation(FLASH_MemType_TypeDef FLASH_MemType));
/**
* @}
*/
#endif /*__STM8S_FLASH_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/